KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第732页
12 − 2 12.1.2 Replacement of 32-mm adhesiv e tape feeder CA UTION Do not replace the tape f eeder with another one while the X- or Y-axis, or head is operating. It m ay cause a serious injury to the operator or dam age t…
12 − 1
CHAPTER 12 HANDLING THE FEEDERS AND
OPTIONS
12.1 Replacement of the Tape Feeder
12.1.1 Replacement of the tape feeder
(8 mm, 12 mm, 16 mm, 24 mm, and 32 mm)
CAUTION
Do not replace the tape feeder with another one while the X- or Y-axis, or
head is operating. It may cause a serious injury to the operator or damage
the machine itself since the tape feeder touches the operating parts.
Do not dismount the tape feeder while the X- or Y-axis or head is operating.
After you mount the feeders required for producing boards at the position
specified with a production program, mount feeders, which are not used for
production, such as 8-mm tape feeders where no feeders are mounted to
prevent any gap from being generated between the already mounted
feeders. This operation secures your safety since it prevents your finger
or hand from accidentally being slid into such a gap.
Mounting
1) Place the bottom of the tape feeder ① on the feeder bank ②
2) Slide the tape feeder ① toward the positioning hole of the fixing plate ③, and
align the guide pin located on the bottom of the tape feeder with the fixing plate
B7 as a guide. Fit the positioning pin on the front of the tape feeder into the
positioning hole of the fixing plate ③. To do so, while pulling the lock release
lever ⑩ gently, align the lock holder ⑨ with the V-shaped groove of the lock
shaft ⑧, then push the front of the tape feeder against the fixing plate. Release
the lock release lever to clamp the lock shaft with the lock holder and fix the tape
feeder.
In this case, the number of the position label ④ pasted just above the hole into
which the positioning pin on the front of the tape feeder is fit indicates the position
at which the tape feeder is mounted.
Note: Check to see if the tape feeder is off the feeder bank or not upright.
Dismounting
1) Hold the tape feeder ① and pull it back to you while pulling the lock release lever
⑩.
10
5
8
2
9
6
3
4
7
1
Figure 12.1.1.1
Note: When the used paper tape (which is ejected from a tape
feeder after a component is supplied from the tape)
warps upward, it may catch in the support section or
other part, then it may cause a tape feeder feeding
error. Check to see if the used tape is ejected
properly.
12 − 2
12.1.2 Replacement of 32-mm adhesive tape feeder
CAUTION
Do not replace the tape feeder with another one while the X- or Y-axis, or
head is operating. It may cause a serious injury to the operator or damage
the machine itself since the tape feeder touches the operating parts.
Do not dismount the tape feeder while the X- or Y-axis or head is operating.
After you mount the feeders required for producing boards at the position
specified with a production program, mount feeders, which are not used for
production, such as 8-mm tape feeders where no feeders are mounted to
prevent any gap from being generated between the already mounted
feeders. This operation secures your safety since it prevents your finger
or hand from accidentally being slid into such a gap.
Mounting
1) Place the bottom of the tape feeder ① on the feeder bank ②.
2) Slide the tape feeder ① toward the positioning hole of the fixing plate ③, and
align the guide pin located on the bottom of the tape feeder with the fixing plate
B7 as a guide. Fit the positioning pin on the front of the tape feeder into the
positioning hole of the fixing plate ③. To do so, while pulling the lock release
lever ⑩ gently, align the lock holder ⑨ with the V-shaped groove of the lock
shaft ⑧, then push the front of the tape feeder against the fixing plate. Release
the lock release lever to clamp the lock shaft with the lock holder and fix the tape
feeder.
In this case, the number of the position label ④ pasted just above the hole into
which the positioning pin on the front of the tape feeder is fit indicates the position
at which the tape feeder is mounted.
3) Match the index of the power cord connector ⑪ with the power supply part ⑬ of
the connector bracket ⑫ (place the white dot to the right), and insert the
connector until you hear a click sound of the click stop.
4) Insert the air coupler ⑮ into the female union ⑭ until you hear a click sound of
the click stop.
5) Set the feeder float sensor that is located on the side a 32-mm adhesive tape
feeder (NF3SN) is installed so that it cannot be used: you uncheck the check
box “Front feeder float detection” or “Rear feeder float detection” on the “Std
Device enable” menu invoked from the Machine Setup menu.
Dismounting
1) Push forward the slide part of the female union ⑭, to detach the air coupler ⑮.
2) Pull the slide part of the power cord connector ⑪ toward your side, and
disconnect the connector.
3) With pulling the lock release lever ⑩, pull back the tape feeder ① to remove it
5
11
14
13
15
12
6
7
8
9
2
1
3
10
4
Figure 12.1.2.1
12 − 3
12.2 Replacement of the Bulk Feeder
CAUTION
Do not replace the bulk feeder with another one while the X- or Y-axis, or
head is operating. It may cause a serious injury to the operator or damage
the machine itself since the bulk feeder touches the operating parts.
Do not dismount the bulk feeder while the X- or Y-axis or head is operating.
After you mount the feeders required for producing boards at the position
specified with a production program, mount feeders, which are not used for
production, such as 8-mm tape feeders where no feeders are mounted to
prevent any gap from being generated between the already mounted
feeders. This operation secures your safety since it prevents your finger
or hand from accidentally being slid into such a gap.
Mounting
1) Place the bottom of the bulk feeder ① on the feeder bank ①.
2) Slide the bulk feeder ① toward the positioning hole of the fixing plate ③, and
align the guide pin located on the bottom of the bulk feeder with the fixing plate B
⑦ as a guide. Fit the positioning pin on the front of the bulk feeder into the
positioning hole of the fixing plate ③. To do so, while pulling the lock release
lever 10 to release the toggle clamp to align the lock holder ⑨ with the V-shaped
groove of the lock shaft ⑧, push the front of the bulk feeder against the fixing
plate. Use the lock release lever to clamp the lock holder and lock shaft by the
toggle clamping method and fix the bulk feeder.
In this case, the number of the position label ④ pasted just above the hole into
which the positioning pin on the front of the bulk feeder is fit indicates the position
at which the bulk feeder is mounted.
Note: 1) Check to see if the bulk feeder is off the feeder bank or not upright.
2) Be sure to fix the case holder on the rear side.
3) Do not mount a bulk feeder on the rear side bank without removing the EIAJ
case
⑪
.
Dismounting
1) Use the lock release lever ⑩ to release the toggle clamp, then pull back the bulk
feeder ① to remove it.
9
6
7
8
2
4
10
5
3
1
11
Figure 12.2.1