KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第773页

13 − 17 A pplyin g Machine Oil to a Nozzle A fter Clean ing It Moisture contained in ethanol or I PA (isopropyl alcohol) may rust t he inner pats of a nozzle if you leave the nozz le without drying it af ter cleaning it …

13 − 16

13.3.4 Nozzle

Clean a nozzle with putting it into a supersonic cleaning bath containing alcohol. After

cleaning, blow off alcohol inside the nozzle with an air gun or similar device, install the

nozzle on the ATC unit again, and perform the "ATC nozzle setup" menu item on the

Machine Setup menu.

Clean a nozzle with a supersonic cleaning bath for five minutes. Dampen soft cloth

with alcohol and use it to clean the urethane part and any part of the nozzle diffuser

on which stains remain stuck to even after you use a supersonic cleaning bath to

clean it.

After cleaning a nozzle, apply New Deflex Oil No. 1 to a nozzle slider to protect the

inside of the nozzle from rust.

Notes: 1. Do not install the nozzle to the head, but install it in the ATC unit.

2. Since the urethane part of nozzles 505, 506, 507 and 508 may be degraded

or flake off when they are damped into alcohol for a long time, turn the

nozzle upside down and insert it to the bath as shown in the figure below so

that any urethane part cannot be dampened into alcohol.

3. Never use any solvent (such as acetone) other than alcohol.

4. Never disassemble a nozzle.

5. After cleaning the nozzle, do no apply any grease other than New Deflex oil

No.1 to it.

6. Be careful not to apply any New Deflex Oil No. 1 to the nozzle diffuser and

rubber section.

Recommended alcohol

We recommend IPA or ethanol due to its cleaning effectiveness, cost and availability.

Recommended solvent : IPA (isopropyl alcohol) or ethanol

Rubber

Beaker

Alcohol

13 − 17

Applying Machine Oil to a Nozzle After Cleaning It

Moisture contained in ethanol or IPA (isopropyl alcohol) may rust the inner pats of a

nozzle if you leave the nozzle without drying it after cleaning it in a supersonic cleaning

bath. Therefore, be sure to apply New Deflex Oil No. 1 (JUKI part number is

MDFRX1001L0) to the nozzle slider.

Use a cotton swab lightly dampened with New Deflex Oil No. 1 to apply this oil to the

part of the nozzle shown below (the part popped up from the nozzle inner section when

you push the nozzle slider). After that, move the nozzle slider up and down 20 to 30

times to apply oil to the nozzle slider thoroughly. Next, remove oil stuck to the exterior

of the nozzle inner section and excessive oil with a clean wiping rag.

Note that nay oil should not be stuck to the nozzle diffuser and rubber section (shaded

section in the figure below).

Be sure to apply only New Deflex Oil No. 1 to the nozzle. If you apply any high

viscosity of oil such as grease to the nozzle, the nozzle slider cannot move back to the

original position easily.

WARNING

Solvent may be flamed. Be careful to handle it. Never use acetone.

Or the diffuser may be discolored. Be sure to wear a mask for organic

gas before cleaning a device. Some ingredient of IPA is hazardous to

humans.

WARNING

To prevent the body from injury which can be caused by accidental

activation of the machine, cut off the power to the machine before

starting to work.

Cotton swab

Small tray

Part to which oil

should be applied

Nozzle inner section

Diffuser

Nozzle slider

Diffuser

Rubber section

20 to 30 times

Clean wiping

13 − 18

13.3.5 Nozzle outer shaft

Stand the nozzle outer shaft as shown in the figure below so that the shaft label

cannot be dampened into any alcohol, and clean it with the ultrasound cleaner.

Clean the shaft with the ultrasound cleaner for ten minutes, which is a guideline.

After cleaning, use an air gun or similar device to blow alcohol from inside the nozzle

outer shaft.

To prevent the shaft from rusting, apply New Deflex Oil No. 1 between the nozzle

outer and the outer SP holder. Apply Albania grease to this area also so that the

shaft can slide more smoothly.

Notes: 1 Never use solution (such as acetone) other than alcohol.

2 Never disassemble the nozzle outer shaft.

3. After cleaning, never use any oil other than New Deflex oil No. 1 or

grease other than Albania grease to the nozzle outer shaft.

−

−−

− About alcohol to be used

We recommend IPA or ethanol due to its cleaning efficiency, cost and availability.

Recommended solvent : IPA (isopropyl alcohol) or ethanol

Nozzle outer shaft

Beaker

Shaft label

IPA