KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第809页

4 Q241302 A nozz le number when calculated from the measurement result and a nozzle number w hen at present is set up differes. Is the nozz le exchanged? Q241303 A pick position is changed. D oes it renew a pick data? E2…

Error Messages on Machine Operations (Tracking)

Error code Message

E240000 The axis cannot be moved

E240001 The axis cannot be moved to escape point

E240002 Yc table cannot be moved

E240003 The axis margin out of range. It is not possible to operation

E240004 The interrupt which was not able to operate was detected. The trace is ended

E240005 The area sensor was detected. Please remove the sensor reaction factor

E240006 The feeder float sensor was detected. Please remove the sensor reaction factor

E240007 Input is mistake

E240008 There is no data previous

E240009 There is no data next

E240010 Specified device cannot be used

E240011 The station is different

E240012 Specified position not move

E240013 The origin point return is non-completion

E240014 The Left OCC device is set in unused by the setup

E240015 The Right OCC device is set in unused by the setup

E240016 The HMS device is set in unused by the setup

Q240500 End tracking?

E241000 Memory allocation error

E241001 Specified device cannot be used

E241002 The station is different

E241003 Specified position not move

E241004 The input value is illegal (%s)

E241005 Index of component data has irregularities (%d)

E241008 Supply of the component is not assign

E241009 Centering of the component is no laser

E241010 Centering of the component is not assign

E241011 No pick data

E241013 Component data is incomplete

E241014 Index of pick data has irregularities. (%d)

E241015 Pick data is incomplete

E241016 Setting the nozzle has not been allocated to ATC. Allocate the nozzle to ATC using TC

nozzle setup function when machine setup. Nozzle no. : %d

E241018 There is no pick data available

E241020 There is no input character

E241021 Input character has irregularities

E241022 Input value exceeds predetermined data range. (Data range : %s - %)

E241023 Component size is too big

E241024 The start no. is larger than the end no.

W241025 Measurement item is not selected

E241026 There is not a measurement possible component

E241028 There is not a inspection possible component

I241200 A continuous measurement ended

I241201 A continuous inspection ended

Q241300 Do you interrupt process?

Q241301 A noz. When calculated from the outline that measured and a noz. When at present is set

up differes. A calculation noz. No. : %3d A setting noz. No. : %3d Does it renew a noz.?

When a noz. Is renewed vacuum level is initialized

Q241302 A nozzle number when calculated from the measurement result and a nozzle number when

at present is set up differes. Is the nozzle exchanged?

Q241303 A pick position is changed. Does it renew a pick data?

E241305 The measurement error occurred. Do you start single measurement?

E241306 The size relation of length and width does not agree with data. | Width : %s(%s)

length : %s(%s) There is possibility that the setting of outline or direction are not fitting. Do

you reflect the measurement result in the component data?

E241307 The inspection error occurred. Do you start single inspection?

Q241308 Is the measurement ended?

Q241309 Is the inspection ended?

E241500 There is no verification device

E241501 The verification device is an unused unit

E241502 Supply of the component is no CVS

E241503 The inspection error occurred

Error Messages on Feeder Bank Recognition

Error code Message

E249001 The origin point return is non-completion. Please operate again after completing the origin

point return

E249002 The OCC device is unused. The bank mark recognition is aborted

E249003 The stop key was pressed. The bank mark recognition is aborted

E249004 The axis cannot be moved to recognition position. The bank mark recognition is aborted

E249005 The bank mark recognition error. The bank mark recognition is aborted

E249006 MTS power off

E249007 MTS cannot move because of cover opening

E249008 The door of MTS opens

E249009 MTS offline

E249010 Servo is in the free state. The bank mark recognition is aborted

Q249051 Feeder bank has descended. Do you want to lift the feeder bank up and continue the bank

mark recognition?

I249070 Set online for MTS

I249071 Please close the door of MTS