KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第876页
71 E316001 “Memory allocation error” [Cause] T he work ing space c an not be saved. [Treatm ent] Please add som e m ore m em or y available to save the work ing spac e. E316002 “Shared memory open error” [Cause] T he sha…
70
Q302014 “Please check if the backup plate is lifted up enough. It may be a
little hard to see pins when the plate is not lifted up. Would you
like to continue?”
[Cause ] When teaching the ref. pin position to the machine, backup plate is checked to
see if it is open or not, and then you are asked if you continue the process.
[Treatment] “YES” button will continue the process.
“NO” button will abort the process.
Q302015 “There may be some units with ON state. Would you like to
initialize these units?”
[Cause] If a driving unit which can possibly be an obstruct is detected when executing the
conveying control of the Mechanical Setup, you are asked if to initialize the unit.
[Treatment] “YES” button will initialize concerned unit(s) and resume the process.
“NO” button will not control the concerned unit(s) and resume the process.
I303000 “Return to home of %s”
[Cause] Z axis and the Theta axis of the ? head will return to Home.
[Treatment] Please hit the “OK” button.
I303001 “Nozzle is removed from %s to ATC”
[Cause] There is a need to remove the nozzle from the ? head.
[Treatment] Please press “OK” button. If you hit the “OK” button, it will return the nozzle on
the ? head to ATC.
I304000 “Set online for MTC”
[Cause] Failed to draw tray out from MTC when teaching in the MTC shuttle pick position
setting since MTC was not online.
[Treatment] Please make MTC online.
I304001 “Remove the nozzle from %s”
[Cause] The nozzle could not be returned automatically since a nozzle installation error
occurred while automatically learning the ATC nozzle allocation. Please remove
the nozzle on the ? head manually.
[Treatment] Please remove the nozzle and then hit the “OK” button.
I304002 “A nozzle of %s is removed and return to %s of ATC”
[Cause] The nozzle could not be returned automatically.
[Treatment] Please remove a nozzle on the ? head manually and return it to the ?? of ATC.
I304003 “Set online for MTS”
[Cause] MTS was not online.
[Treatment] Please make MTS online.
I304004 “Please close the door of MTS”
[Cause] Failed to draw the MTS tray out since the MTS door was open.
[Treatment] Please close the MTS door.
71
E316001 “Memory allocation error”
[Cause] The working space can not be saved.
[Treatment] Please add some more memory available to save the working space.
E316002 “Shared memory open error”
[Cause] The shared memory could not be open.
[Treatment] Please shut down the your machine and re-start it.
E316011 “There is no input character”
[Cause] There was no character when you hit Enter key to define characters.
[Treatment] Please enter characters.
E316012 “Input character has irregularities”
[Cause] The letter strings had irregularities when defining the input.
[Treatment] Please enter proper characters.
E316013 “Input value exceeds predetermined data range”
[Cause] The value when defining the input exceeded the input range.
[Treatment] Please enter the values that are within the range.
E316021 “Return to home has not yet been completed”
[Cause] The axis has not yet been returned to home.
[Treatment] Please perform the Return to home with ORIGIN switch.
E316022 “Servo is in the free state”
[Cause] The axis could not move since the servo is not locked.
[Treatment] Please lock the servo with S-FREE switch.
E316031 “Selected device is not install. Please reselect other device on HOD”
[Cause] You could not go into the teaching mode since the device selected by HOD has
not been installed.
[Treatment] Please reselect the device which is currently installed.
W316041 “There is no ATC that is allocated with nozzle. Allocate nozzle to
ATC when setting up the machine”
[Cause] Although Nozzle change was chosen in ATC control, no nozzle has been
assigned to the ATC.
[Treatment] Please allocate nozzles to ATC in ATC Nozzle allocation in Machine Setup.
W316042 “Nozzle is not set on head”
[Cause] Although Nozzle returning was chosen in ATC control, no nozzle has been
installed on the specified head.
[Treatment] Please install a nozzle on the head, then try again.
72
E316051 “Z axis limit has been exceeded”
[Ｃause] Z axis coordinate exceeded its limit. The axis can not move any further.
[Treatment] Please move the axis within the limitation.
E316101 “Error has occurred when setting laser parameters code:%ld”
[Cause] An abnormal matter happened when setting the Laser parameter.
?: Error code.
-1: A communication error occurred.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316102 “Error has occurred during laser measurement(ONCE) code:%ld”
[Cause] An error occurred during the measurement(ONCE) by laser.
?: Error code.
-1 : A communication error.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316103 “Error has occurred during laser measurement(SWEEP) code:%ld”
[Cause] An error occurred during the measurement(SWEEP) by laser.
?: Error code
-1: A communication error occurred.
-2: An axis error occurred
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316104 “Error has occurred during the nozzle presence check code:%ld"
[Cause] An error occurred during the measurement(ONCE) by laser.
?: Error code.
-1 : A communication error.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316105 “Error has occurred during the image data obtain. code:%ld"
[Cause] An error occurred while getting the Image data by laser.
?: Error code
-1: A communication error occurred.
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316106 “Error has occurred during the edge check data learning.
code:%ld"
[Cause] An error occurred while getting the Edge check by laser.
?: Error code.
-1: A communication error occurred.
Other: Please reference [Status list] in [Laser Control] in Manual Control
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316107 “Data has not been learned”
[Cause] Z axis coordinate by HMS could not be learned since it was out of the