KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第894页
89 E501203 “DTS is not in t he executable st atus. Would you like to have DTS return to Home positi on?” [Cause] T his er ror occ urs if DTS Hom e r eturning has not been c om plete when starting a production. [Treatm en…
88
E501018 “Component exists on the MTC Shuttle. Please Remove Component
from Shuttle”
[Cause] This error occurs if any components are on the shuttle of MTC when starting a
production.
[Treatment] Please remove those components from the MTC shuttle and press OK button.
E501019 “Because MTC is Change Component Condition, home position
return cannot be done. Please Release the Change condition”
[Cause] This error occurs if MTC is in a status where MTC needs a component change
when performing the Home returning of MTC.
[Treatment] Please disable the status of MTC, and press OK button.
E501100 “MTS power off”
[Cause] MTS was not ON when starting a production.
[Treatment] Please turn on the power supply of MTS and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501101 “MTS offline”
[Cause] MTS was not online when starting a production.
[Treatment] Please put MTC in online status and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501102 “MTS cannot move because of cover opening”
[Cause] MTS cover was open when starting a production.
[Treatment] Please close the MTS cover and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501103 “The door of MTS opens”
[Cause] MTS door was open when starting a production.
[Treatment] Please close the MTS door and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501200 “Communication error of DTS occurred”
[Cause] An error occurred in DTS.
[Treatment] This is a DTS internal error. Please take a note of the error number and contact
our technical service dept. for information.
E501201 “DTS status got an error. The process can not be performed”
[Cause] This error occurs if DTS is in an error status when starting a production.
[Treatment] Please turn off the power supply of DTS and examine it.
E501202 “DTS’ cover is open. Please close the cover”
[Cause] This error occurs if DTS cover is open when starting a production.
[Treatment] Please close the DTS door and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
89
E501203 “DTS is not in the executable status. Would you like to have DTS
return to Home position?”
[Cause] This error occurs if DTS Home returning has not been complete when starting a
production.
[Treatment] OK button : Performs DTS Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501204 “DTS is not in the executable status. Would you like to have DTS
return to Home Position?”
[Cause] This error occurs if DTS is in the executable status when starting a production.
[Treatment] OK button : Performs Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501205 “DTS is in the supplying status. Please release DTS from the status”
[Cause] This error occurs if DTS is in the supplying status when starting a production.
[Treatment] Please disable the supply status of DTS and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501300 “No tracing data”
[Cause] This error occurs if there is not data to trace on the specified station when
executing tracing.
[Treatment] Please press OK button to continue the process.
E501400 “[Vision] Memory access error”
[Cause] There is not enough memory.
[Treatment] Please re-start the application.
E501401 “[Vision] Failed to collect System condition data”
[Cause] The system information is wrong.
[Treatment] Please re-boot your machine.
E501402 “[Vision] Failed to collect Mark recognition condition data”
[Cause] The entered mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the mark data.
E501403 “[Vision] Failed to collect Component recognition condition data”
[Cause] The entered vision data is not correct.
[Treatment] Please go to the Production Program Editor and check the mark data.
E501404 “[Vision] Failed to transmit System condition data to the Vision
board”
[Cause] The system information is wrong.
[Treatment] Please re-boot your machine.
E501405 “[Vision] Failed to transmit Bankmark recognition condition data to
90
the Vision board”
[Cause] The entered bankmark data is not correct.
[Treatment] Please re-boot your machine.
E501406 “[Vision] Failed to transmit BOC mark recognition condition data to
the Vision board”
[Cause] The entered BOC mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the PWB data.
E501407 “[Vision] Failed to transmit IC mark recognition condition data to
the Vision board”
[Cause] The entered IC mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the Placement data.
E501408 “[Vision] Failed to transmit Component recognition condition data
to the Vision board”
[Cause] The entered vision data is not correct.
[Treatment] Please go to the Production Program Editor and check the Vision data.
E501409 “[Vision] Data index error exceeds the specified range”
[Cause] This is a program error.
[Treatment] Please take a note of the error code and contact our technical service dept. for
information.
E501410 “[Vision] Unknown request (Program error)”
[Cause] This is a program error.
[Treatment] Please take a note of the error code and contact our technical service dept. for
information.
E503001 “Retry List message file (RETRYLIST.MSG) cannot be opened”
[Cause] Failed to open the Retry List message file.
[Treatment] Please re-install the system.
E503100 “You try to set remain less than level now, OK?”
[Cause] The number of components remaining becomes less than the warning level of the
number of components left.
[Treatment] Yes : Sets the entered number of components remaining.
No : Gets you back to the number of components remaining that is before you
set.