KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第896页
91 E503200 “It is not Program made by setting non-stop. A normal operation i s not occasionall y done when producing as it is. Product ion start forcibly ?” [Cause] T his m es sage appears when the Non-stop func tionalit…
90
the Vision board”
[Cause] The entered bankmark data is not correct.
[Treatment] Please re-boot your machine.
E501406 “[Vision] Failed to transmit BOC mark recognition condition data to
the Vision board”
[Cause] The entered BOC mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the PWB data.
E501407 “[Vision] Failed to transmit IC mark recognition condition data to
the Vision board”
[Cause] The entered IC mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the Placement data.
E501408 “[Vision] Failed to transmit Component recognition condition data
to the Vision board”
[Cause] The entered vision data is not correct.
[Treatment] Please go to the Production Program Editor and check the Vision data.
E501409 “[Vision] Data index error exceeds the specified range”
[Cause] This is a program error.
[Treatment] Please take a note of the error code and contact our technical service dept. for
information.
E501410 “[Vision] Unknown request (Program error)”
[Cause] This is a program error.
[Treatment] Please take a note of the error code and contact our technical service dept. for
information.
E503001 “Retry List message file (RETRYLIST.MSG) cannot be opened”
[Cause] Failed to open the Retry List message file.
[Treatment] Please re-install the system.
E503100 “You try to set remain less than level now, OK?”
[Cause] The number of components remaining becomes less than the warning level of the
number of components left.
[Treatment] Yes : Sets the entered number of components remaining.
No : Gets you back to the number of components remaining that is before you
set.
91
E503200 “It is not Program made by setting non-stop. A normal operation is
not occasionally done when producing as it is. Production start
forcibly?”
[Cause] This message appears when the Non-stop functionality is enabled in the
Operation Option but the production program does not take Non-stop.
[Treatment] Please disable the Non-stop functionality in the Operation Option, or check the
Pick data in the production program.
E503300 “%s feeder bank is in lower position”
[Cause] This message appears if a feeder bank is descending down when starting a
production.
? : where the feeder bank is descending to.
On the front side
On the rear side
On both sides.
[Treatment] Please press OK button after the feeder bank has ascended.
E503301 “MTC is in motion. Please wait for stop”
[Cause] This message appears if MTS is in operation when starting a production.
[Treatment] Please press OK button after MTC’s motion has been done. Pressing Cancel
button will have you back to the status that is before pressing START key.
E503302 “Cover open”
[Cause] This message appears at the beginning of a production if the production can not
be produced with the cover open.
[Treatment] Please close the cover and press the START key again.
E503400 “The sequence(%s) you selected is different from the one(%s) of
when the production got suspended illegally last time. Would you
like to resume the production?”
[Cause] This message appears if the current sequence and the previous sequence are
different from each other when resuming the production.
? : Sequence
Input order
Optimization order
[Treatment] OK button : Starts the production with the sequence being different from the
previous one. There is a possibility that PWBs will be incomplete.
Cancel button : Will have you back to the status that is before pressing START
key.
92
E503401 “The Production start No. that is currently set(%s) is larger than the
one(Left:%s Right:%s) of when the production got suspended
illegally last time. Would you like to start the production though the
PWB may become incomplete?”
[Cause] This message appears if current production start No. is larger than the one of
when the production got suspended illegally last time when resuming the
production.
[Treatment] OK button : Starts the production with current production start No.
(Placement data index) being larger than the previous one.
There is a possibility that PWBs will be incomplete.
Cancel button : Will have you back to the status that is before pressing START key.
E503402 “The Production stop No. that is currently set (%s) us smaller than
the one (Left:%s Right:%s) of when the production got suspended
illegally last time. Would you like to start the production though the
PWB may become incomplete?”
[cause] This message appears if current production stop No. is smaller than the one of
when the production got suspended illegally last time when resuming the
production.
[Treatment] OK button : Starts the production with current production stop No.
(Placement data index) being smaller than the previous one.
There is a possibility that PWBs will be incomplete.
Cancel button : Will have you back to the status that is before pressing START key.
E503500 “No completion change plan. Please use Feeder Bank”
[Cause] This message appears if Non-stop production is set in the Operation Option and
the feeder bank on the front side is descending down when reading a file in.
[Treatment] Please have the feeder bank ascend.
E506100 “You can resume the production from the last suspended position
|%s|%s| Would you like to resume the production?”
[Cause] This message appears if the production is resumable when reading a file in.
?? : Resumptive production starting position of each station.
[Treatment] Yes : Starts the production from the placement point which got illegal abortion
last time.
No : Will not resume the production but start a normal production that is set in
the Production Condition.
E506101 “You need to delete the file if you do not resume the production
from the last illegally suspended position.
%s
%s
Would you
like to delete the file?”
[Cause] This message appears if you select ‘do not resume the production’ when you are
asked if to resume the production when reading a file in or the Production screen
got started.
[Treatment] Yes : Deletes the resumable production file. If you delete the file, you can no
longer resume the production from the point where the production got
illegal abortion.
No : Will not delete the resumable production file.