00192375-01 - 第12页
SIPLACE GEM for S25, HS50 SW Version GEM 502.01 HOST Inter face Manual Page 12 of 236 ©Siem ens AG, all rights reser ved (TXLSPHQ W The SIPLACE S25 or SIPLACE HS50 with GEM/SECS II-Interf ace 2SHUDWRU The pers on who phy…
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
©Siemens AG, all rights reserved page 11 of 236
1.4 *(0&RPSOLDQFH6WDWHPHQW
GEM COMPLIANCE STATEMENT
FUNDAMENTAL GEM REQUIREMENTS IMPLEMENTED
COMPLIANT
State Models ✓ Yes ✓ Yes
Equipment Processing States ✓ Yes ✓ Yes
S1,F13/F14 Scenario ✓ Yes ✓ Yes
Event Notification ✓ Yes ✓ Yes
On-line Identification ✓ Yes ✓ Yes
Error Messages ✓ Yes ✓ Yes
Control (Operator Initiated) ✓ Yes ✓ Yes
Documentation ✓ Yes ✓ Yes
ADDITIONAL CAPABILITIES IMPLEMENTED COMPLIANT
Establish Communications ✓ Yes ✓ Yes
Dynamic Event Report Configuration ✓ Yes ✓ Yes
Variable Data Collection ✓ Yes ✓ Yes
Trace Data Collection ✓ Yes ✓ Yes
Status Data Collection ✓ Yes ✓ Yes
Alarm Management ✓ Yes ✓ Yes
Remote Control (1) ¨ No ¨ No
Equipment Constants ✓ Yes ✓ Yes
Process Program Management (2) ¨ No ¨ No
Material Movement ✓ Yes ✓ Yes
Equipment Terminal Services ✓ Yes ✓ Yes
Clock ✓ Yes ✓ Yes
Limits Monitoring ✓ Yes ✓ Yes
Spooling ✓ Yes ✓ Yes
Control (Host Initiated) ✓ Yes ✓ Yes
(1) : Remote commands are not available until a later stage.
(2) : Process Program Management is not implemented until a later stage.
7HUPLQRORJ\
The following terms are used throughout the document to refer to the various entities
interfacing with the SIPLACE:
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
Page 12 of 236 ©Siemens AG, all rights reserved
(TXLSPHQW The SIPLACE S25 or SIPLACE HS50 with GEM/SECS II-Interface
2SHUDWRU The person who physically has access to the equipment’s material port(s)
and control panel. This is the person who is operating the SIPLACE.
+RVW The computer which is connected to the equipment via the SECSII-interface
0DFKLQH$UHDV
0DFKLQH$UHDVRID6,3/$&(+60DFKLQH
The figure below provides a diagrammatic overview of the individual areas of a
SIPLACE HS-50 placement station.
TWIN-Input
conveyor
TWIN-First
Processing
conveyor
TWIN-Output
conveyor
Input
conveyor
First Processing
conveyor
Output
conveyor
Direction of transport
Conveyor 2
(left)
Conveyor 1
(right)
Gantry 3
Revolverhead 3
Gantry 2
Revolverhead 2
Location
3
Location
2
TWIN-Inter-
mediate conveyor
TWIN-Second
Processing
conveyor
Intermediate
conveyor
Second Processing
conveyor
Gantry 4
Revolverhead 4
Location
4
Gantry 1
Revolverhead 1
Location
1
Processing 1
Area
Processing 2
Area
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
©Siemens AG, all rights reserved page 13 of 236
1.6.2 0DFKLQH$UHDVRID6,3/$&(60DFKLQH
The layout of the feeder locations of the S25 machine depends on the configuration of the
individual machine. If there is an MTC on one side of the machine, the locations are
divided. Otherwise they are grouped into one location. The following figures illustrate the
individual variants.
The figures shows the machine areas of an S25 with dual conveyor and 2 MTCs.
The conveyor belts are divided into 3 areas. There are 4 feeder locations.
TWIN-Input
conveyor
TWIN-First
Processing
conveyor
TWIN-Output
conveyor
Input
conveyor
First Processing
conveyor
Output
conveyor
Direction of transport
Conveyor 2 (left)
Conveyor 1 (right)
Gantry 1
Revolverhead 1
Gantry 2
Revolverhead 2
Location
3
07&
Location
4
Location
2
Location
1
07&