00194440-10_SM_X-Series_Customer_en - 第105页
Service Work 3.3.8 Replacing the Trailing Cable Gantries Service Manual SIPLACE X Series 105 Conversion for SIPL ACE HF up to A 219 These versions of the trailing cable can also be used with SIPL ACE HF machines up to ma…
Service Work
Gantries 3.3.8 Replacing the Trailing Cable
104 Service Manual SIPLACE X Series
► Shorten the pneumatic hoses to the optimum length.
Make sure that they are not too long or too short.
They must engage firmly but should not buckle.
► Reconnect to the compressed air supply. Observe
the correct connector assignment.
► Loosely fasten the pressure plates (6) to the machine
base.
► Check that the power track chain can run along the
top of the machine base without obstruction. Move
the Y axis back and forth to check this.
► If necessary, correct at the trailing cable console (1)
and at the pressure plates.
► Fix the two pressure plates (6) and the trailing cable
console (1). Use Loctite 241 locking varnish to secure
them.
► Tighten the fastening screws for the trailing cable
console (1) crosswise.
► Reconnect the cooling tubes to the Y motor.
► Fit the 3 pressure plates (1) at the gantry and head
mount (2).
► You will need to replace the cable supports for
SIPLACE HF machines up to MA219. See also
"3.3.8.5.4 Conversion for SIPLACE HF up to A 219"
[ ➙ 105].
► Fit the head board (3). Make sure you do not lose the
contact disks or spacer bolts.
► Plug in all connections/terminals. Observe the cor-
rect connector assignment.
► Fasten new cable ties at the original points.
► Replace all dismantled cover plates in their original
positions.
2
5
4
6
6
1
3
5
1
3
2
Service Work
3.3.8 Replacing the Trailing Cable Gantries
Service Manual SIPLACE X Series 105
Conversion for SIPLACE HF up to A 219
These versions of the trailing cable can also be used with SIPLACE HF machines up to machine number
A-219, in conjunction with the "Trailing cable retrofit kit" 03046248-01.
▪ Trailing cable for HF machines with one gantry
– [03039706S01] Trailing cable analog 1P
▪ Trailing cable for HF machines with two gantries in uneven locations (1 and 3)
– [03039708S01] Trailing cable analog 2P U
▪ Trailing cable for HF machines with two gantries in even locations (2 and 4)
– [03039709S01] Trailing cable analog 2P G
The difference lies in the fact that the new pressure plate
can no longer be fastened to the existing cable support.
The old cable support (1) therefore needs to be replaced
with a new one.
► Replace the old cable support (1) with the new cable
support (2) from the retrofit kit. The new cable sup-
port has four drilled holes (3) for fastening the new
pressure plate.
► Fit the pressure plate for the new trailing cable onto
the new cable support, with the four M3x35 screws
from the retrofit kit.
► If the pressure plate on the gantry does not fit into the
existing holes drilled, loosen the clamp on the pres-
sure plate and shift it accordingly.
► Tighten the clamp again and fit the pressure plate at
the correct position of the gantry drillings.
Service Work
Gantries 3.3.8 Replacing the Trailing Cable
106 Service Manual SIPLACE X Series
3.3.8.6
3.3.8.6 Replacing the Trailing Cable for X Series Machines up to B-078 [03003199-xx]
Replacing the Trailing Cable for X Series Machines up to B-078 [03003199-xx]
Parts
▪ Trailing cable, digital 1P [03015419-03]
▪ Trailing cable, digital 2P U [03002306-03]
▪ Trailing cable, digital 2P G [03003199-03]
▪ Hose pliers for cutting the pneumatic hose
▪ Pipe/hose cutters [00381443-xx]
▪ Hose unlocking tool [03047090-xx]
▪ Sealing varnish Loctite 241 [02101037-xx]
Preparation
The trailing cable is supplied as a complete assembly. In accordance with your machine's configuration,
you will need to remove the relevant modules, covers and cover plates before you can dismantle the
trailing cable.
► Where necessary, remove the cover plates from the gantry trailing cable. Mark their exact position
to ensure correct replacement later.
► Remove the top central cover from the SIPLACE machine.
► Remove the upright covers over the trailing interface gantry, so that you can reach the trailing cable.
CAUTION!
Some of the machines up to number B-078 have been
converted to accommodate the new trailing cable from
number B-079. Before ordering the trailing cable, please
compare the item numbers on your current machine. The
conversion of a customer machine involves significant
costs and is only possible at the SIPLACE headquarters.
If the trailing cable has the additional white hoses (1), this
is a new trailing cable.