00194440-10_SM_X-Series_Customer_en - 第148页

Service Work C&P20 Nozzle Changer 3.5.7 Installation and Height Adjustment of Nozzle Station (De scription for 148 Service Manua l SIPLACE X Series 1. Dummy plu gs 2. Throttle valve 3. Fine throttle 4. Hose 5. T-piec…

100%1 / 384
Service Work
3.5.6 Replacing the Complete Lever/Toggle [03013445-xx] C&P20 Nozzle Changer
Service Manual SIPLACE X Series 147
3.5.6
3.5.6 Replacing the Complete Lever/Toggle [03013445-xx]
Replacing the Complete Lever/Toggle [03013445-xx]
Removal/installation
3.5.7
3.5.7 Installation and Height Adjustment of Nozzle Station (Description for Docking Unit [03015680-06] with 1-Wire-Hub)
Installation and Height Adjustment of Nozzle Station (Description for Docking Unit
[03015680-06] with 1-Wire-Hub)
1. Toggle
2. Fastening screw
► Loosen the screw (2) holding the toggle (1).
► Remove the toggle (1), insert a new one and fix this
with the fastening screw (2).
1. T-piece on component trolley feed device
► Disconnect the pneumatic hose from the COT insert.
Service Work
C&P20 Nozzle Changer 3.5.7 Installation and Height Adjustment of Nozzle Station (Description for
148 Service Manual SIPLACE X Series
1. Dummy plugs
2. Throttle valve
3. Fine throttle
4. Hose
5. T-piece press-fit connection QSMT-4
► Use the T-piece and PUN hose from the component
trolley feed device to connect the T-piece "press-fit
connection QSMT-4" [03046434-xx] (5) with the
PUN-CM 4x0.75 40 mm [03046289-xx].
► Fit the "Fine throttle GRO-QS-4-LF"
[03045754-xx] (3) with the screws "DIN912 M3x18 -
A2-70" [03045034-xx] onto the "holding plate for
throttle" [03046270-xx] and then fix all this to the tape
feed channel with the screws "DIN7981 ST3.5x6.5-C-
H-A2" [03046777-01] (see photo).
► Remove the "Plug QSC-4H" [00330249-xx] for set-
ting the air blast (see photo).
► Use the two T-pieces to connect the throttle valve
with the "PUN-CM 4x0.75 70 mm" - hoses
[03046291-xx].
1. Nozzle station
2. Hose PUN-CM 4x0.75 420 mm
3. Cable clamp
4. Hose run correctly
► Fit the nozzle station [03045404-xx] (1) with the two
screws "DIN7991 M4x20 - 8.8" [00333782-xx].
► Run the long hose "PUN-CM 4x0.75 420 mm"
[03046432-xx] (2) up to the T-piece (see photo).
► Secure this hose with a cable clamp "Clamp Panduit
CC S12-S08 D3.1 b 8.2" [00368063-xx] (3) and a
screw "DIN912 M3x6 - A2-70" [03045028-xx].
CAUTION!
Make sure that the hose is run in front of the holding plate
for the 1-wire hub (4).
Service Work
3.5.7 Installation and Height Adjustment of Nozzle Station (Description for Docking Unit [03015680-06] with 1-Wire-Hub) C&P20 Nozzle Changer
Service Manual SIPLACE X Series 149
Compressed air setting
1. Measuring device
2. Fine throttle
► Connect the compressed air measuring device to the
T-piece (plug).
► Use the fine throttle to set a pressure of 0.5 bar.