00194440-10_SM_X-Series_Customer_en - 第229页
Service Work 3.10.4 Replacing the Centering Sleeves [03009987-xx] X-Series Co mponent Trolley Service Manual SIPLACE X Series 229 3.10.4 3 . 1 0 . 4 R e p la c in g t h e C e n t e r in g S le e v e s [ 0 3 0 0 9 9 8 7 -…
Service Work
X-Series Component Trolley 3.10.3 Replacing the Guide Profile/Entering Guide Feeder
228 Service Manual SIPLACE X Series
► During reassembly, take care to keep the pressure plates in their correct position (4). These are not
symmetrical and will not hold the shaft properly if placed in a certain (incorrect) position.
► When tightening the fastening screws (3), make sure that the pressure plates (4) are not at an incor-
rect angle and that the locking latches do not jam.
► Hook the tension springs (1) back up.
► Refit the cover.
3.10.3
3.10.3 Replacing the Guide Profile/Entering Guide Feeder
Replacing the Guide Profile/Entering Guide Feeder
Parts, equipment and tools
▪ Guide profile [03002898-xx]
or
Entering guide feeder [03039368 -xx]
Overview
► Unhook all tension springs (1) from the locking latch-
es (2).
► Loosen the screws (3) fastening the pressure plates
(4).
► Pull out the locking latches with the shaft (5).
► The locking latches can now be pushed off the shaft.
► Return the locking latches, including the new one, to
the shaft.
► Fit the locking latches and shaft.
4
5
1
3
2
1. Short guide profile
2. Entering guide feeder
The guide profiles are fixed from above, with one screw
each.
The feeder entering guide is fixed from below, with three
screws each.
1
2
Service Work
3.10.4 Replacing the Centering Sleeves [03009987-xx] X-Series Component Trolley
Service Manual SIPLACE X Series 229
3.10.4
3.10.4 Replacing the Centering Sleeves [03009987-xx]
Replacing the Centering Sleeves [03009987-xx]
Parts, equipment and tools
▪ Centering sleeve [03009987-xx]
▪ Loctite 243 [00334892-xx]
Overview
Removal
► Loosen the screw fastening the centering sleeve and then remove the centering sleeve.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
NOTICE
Replacing all sleeves.
We recommend that you always replace all sleeves belonging to a changeover table at the
same time.
1. Centering sleeves (four per table)
CAUTION
Installation instructions
► Secure the screws with Loctite 243.
Service Work
X-Series Component Trolley 3.10.5 Replacing the Insert Feeder [03002898-xx]
230 Service Manual SIPLACE X Series
3.10.5
3.10.5 Replacing the Insert Feeder [03002898-xx]
Replacing the Insert Feeder [03002898-xx]
Parts, equipment and tools
Select the right insert feeder:
Removal
► Move the component trolley out of the machine.
► Loosen the screw fastening the guide profile and remove the guide profile.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
Insert feeder [03002898-xx]
Suitable for:
▪ X-Series component trolley
▪ Component trolley SX1/SX2 (30 or 60 tracks)
▪ Manual table X-Series S
Insert feeder [03085635-xx]
Suitable for:
▪ Manual table DX series
CAUTION
Installation instructions
► Make sure that the insert is aligned properly with the guidance behind it. You must be able
to push feeder modules into the feeder location without edge interference.