00194440-10_SM_X-Series_Customer_en - 第62页
Service Work Electrics and Control 3.1.5 Replac ing the Axis Unit Assemblies [ 00353054-xx] 62 Service Manual SIPLACE X Series 3.1.5 3 . 1 . 5 R e p la c in g t h e A x is U n it A s s e m b lie s [ 0 0 3 5 3 0 5 4 - x x…
Service Work
3.1.4 Replacing the Axis Unit with Adapter Cable (X, D Series) Electrics and Control
Service Manual SIPLACE X Series 61
► Fit the adapter cable harness (2) holder to the left in-
side panel of the axis unit, with the two screws
provided (1).
Axis unit, new
► Connect the adapter harness connectors to the con-
nection points in the new axis unit, as follows:
1. Connection for connector X11_3*q
2. Connection for connector X47*q
3. Connection for connector X08_3*q
4. Connection for connector X46*q
5. Connection for connector X09_3*q
6. Connection for connector X42_1*q
7. Connection for connector X41_1*q
8. Connection for connector X04_3*q
9. Connection for connector X03_3*q
10. Connection for the ballast resistance
11. Four connections X and Y motors for the connectors
(from top to bottom) X4tr, X4tt, X4ur and X4ut.
Two or four connections are used, depending on the
machine type.
12. Connection for connector X10_3*q
13. Connection for connector X07_3*q
14. Connection for connector X1we
15. Connection for connector X12_3*q
16. Connection for connector X45*q
17. Connection for connector X2we
► Reconnect the cables for the X and Y motor (11) con-
nections with cable clamps, to the back of the axis
unit.
Service Work
Electrics and Control 3.1.5 Replacing the Axis Unit Assemblies [00353054-xx]
62 Service Manual SIPLACE X Series
3.1.5
3.1.5 Replacing the Axis Unit Assemblies [00353054-xx]
Replacing the Axis Unit Assemblies [00353054-xx]
Adapter cable harness
► Connect the Harting connector (1) of the adapter ca-
ble harness to the relevant connection point on the
machine.
► Hook the axis unit back into the guide rail in the ma-
chine. Carefully stow the cables in the machine.
CAUTION!
Make sure you do not damage any cables. Pay particular
attention to the lower part of the flat ribbon cable harness
(1). Make sure this does not rub against any parts.
► Push the axis unit into the machine and fit the protec-
tive cover.
► Switch the machine back on and perform a function
test.
► End all placement operations on the machine.
► Switch the placement system off at the main switch
(1).
► Remove the cover on the axis unit (2).
1
2
Service Work
3.1.5 Replacing the Axis Unit Assemblies [00353054-xx] Electrics and Control
Service Manual SIPLACE X Series 63
3.1.5.1
3.1.5.1 Overview of Axis Unit (with A363) [00353054-xx]
Overview of Axis Unit (with A363) [00353054-xx]
Axis unit with A363: configuration example C&P20 and
C&P20
The axis card A363 was fitted up to machine number B-
336.
The plug-in cards vary according to the machine configu-
ration. This example shows an axis unit with two C&P20
heads in placement area 1.
1. Brake board for each X axis and Y axis
2. Servo amplifier X axes
3. Star axis servo amplifier
4. Servo amplifier Z axis
5. Power supply +/- 15, +5 V
6. Ballast circuit (only in axis unit PA2)
7. Servo amplifier Y axes
8. Fan unit
9. DC/DC converter, DP drives
10. Power supply +/- 15V
11. Anti-crash board
12. Axis controller boards