00192299-02 - 第67页
SIPLACE HS-50 2 Retrofitting Instructions: Mechanical Ceramic Subs trate Centering HS-50 01/01 Issue 2.2 Safety Instructions 67 6DIHW\,QVWUXFWLRQV DANGER Only Sie mens ser vice e ngineers ar e permi tted to per form…
2 Retrofitting Instructions: Mechanical Ceramic Substrate Centering HS-50 SIPLACE HS-50
2.1 Overview 01/01 Issue
66
– The conveyor assemblies are converted for use of the mechanical ceramic substrate centering
unit (X-centering unit) by installing the holddowns from the retrofit kits.
– The appropriate stop rail and the appropriate stop unit (kit 1, 2 or 3) are mounted on the X-
centering unit to adapt it to the substrate size to be processed: 50 mm to 140 mm. These parts
are available, preassembled, in the retrofit kit (see Section 2.4 and Section 2.5.9).
NOTE:
On request, it is possible to perform a retrofit kit for the "mechanical ceramic substrate centering
unit HS-50" for machines HS-50 with optinal "PCB conveyor, left".
This retrofitting is not described here but can be executed in a like manner.
SIPLACE HS-50 2 Retrofitting Instructions: Mechanical Ceramic Substrate Centering HS-50
01/01 Issue 2.2 Safety Instructions
67
6DIHW\,QVWUXFWLRQV
DANGER
Only Siemens service engineers are permitted to perform the retrofitting of the "Mechanical ce-
ramic substrate centering HS-50".
Comply with the higher ranking "Safety Instructions" in Chapter "Operational Safety" in the User
Manual and Service Manual.
The machine SIPLACE HS-50 is powered by
219/380 V +/- 5% or
230/400 V +/- 5% or
239/415 V +/- 5% or
117/204 V +/- 5% or
133/230 V +/- 5%,
50/60 Hz line voltage.
Portions of the system are therefore conducting dangerous electricity, inside the machine even
while the master switch is turned off.
After you have properly carried out the shut-down of the Windows operating system NT:
BEFORE all work the machine must be turned OFF at the main switch and isolated from the
mains. In addition, the compressed air supply must be turned off at the main valve of the com-
pressed air unit in the machine base and the compressed air lines must be bled by actuating the
needle valve at the compressed air unit (particularly due to the risk of injury - posed by residual
air - at the pneumatic cutter and because of the work required in the compressed air branch).
Obey the applicable accident prevention regulations, DIN standards and special safety codes of
your country at all times. DIN EN 60204 must be adhered to during all work inside the machine
base.
Follow the instructions regarding residual voltages in Chapter "Operational Safety"
Comply with regulations on ESDs (see Chapter "Operational Safety"), e.g., when working on the
conversion PCB for the PCB conveyor control.
During the work of retrofitting secure the machine conscientiously against other personnel and
prevent it from being turned back on without authorization, as described in the User Manual in the
chapter "Locking the Machine...".
There is additional, higher risk of accident when working with the SITEST program.
The SIPLACE program is only to be started by personnel who are authorized to do so.
For the work with the SITEST program the component changeover table must be moved in and
correctly connected.
2 Retrofitting Instructions: Mechanical Ceramic Substrate Centering HS-50 SIPLACE HS-50
2.2 Safety Instructions 01/01 Issue
68
'HILQLWLRQV
DANGER
in terms of these instructions means that death, severe bodily injury or considerable material dam-
age WILL occur if the instructions about danger are not followed.
WARNING
in terms of these instructions means that death, severe bodily injury or considerable material dam-
age may occur if the warnings are not heeded.
CAUTION
in terms of these instructions mean that minor bodily injury or material may occur if the cautions
are not heeded.
NOTE
in terms of these instructions is a statement of important information about the product or the
pertinent portion of the instructions to which particular attention is being drawn.