SIPLACE-SX4-DX4-用户手册 - 第112页
Service Work Conveyor 3.6.9 Replacing the Conveyor Drive [03075892-xx] 112 Service Manual SIPLACE SX4/DX4 Installation ► Follow the removal in structions in reverse order for installati o n. Also observe the following in…
Service Work
3.6.9 Replacing the Conveyor Drive [03075892-xx] Conveyor
Service Manual SIPLACE SX4/DX4 111
► When you remove the conveyor drive at location 4, move the adjustment units over to locations 3
and 4, at the side. This makes unintentional maladjustment more difficult. (See "3.6.14 Replacing the
Width Adjustment Toothed Belt [03076223-xx]" [ ➙ 118])
Then loosen the width adjustment belt, giving you access to unthread the width adjustment drive.
► Loosen the screws (3) fastening the hexagonal shafts
(2) over the conveyor drive (1) and move this drive
carefully within its drilled holes in the machine base.
(See also "3.6.18 Replacing the Hexagonal Shaft
[03057258-xx]" [ ➙ 122])
CAUTION!
There are cables run inside the machine frame.
Make sure you do not damage these cables.
Conveyor drive mount, shown here with the width adjust
-
ment drive
► Unplug the electrical connections to the conveyor
drive (1) and, if present, to the width adjustment
drive (2). Loosen the corresponding cable ties, if re-
quired.
NOTICE!
Single conveyor
You do not need to remove the mount for single convey-
ors, as there is more room next to the conveyor in this
case.
Conveyor drive mount, shown here with the width adjust
-
ment drive
► If the cover plate for the input/output conveyor is fas-
tened to the mount, loosen the relevant fastening
screws.
► Lift the plate slightly upwards to release it from the
mount and then place it down below the conveyor.
CAUTION!
Make sure you do not damage any cables.
Service Work
Conveyor 3.6.9 Replacing the Conveyor Drive [03075892-xx]
112 Service Manual SIPLACE SX4/DX4
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.6.1 Loosening the Conveyor Side Clamps [ ➙ 95]
3.6.13 Replacing the Width Adjustment Drive [03078341-xx] [ ➙ 117]
3.6.14 Replacing the Width Adjustment Toothed Belt [03076223-xx] [ ➙ 118]
► Loosen the 3 screws (3) fastening the mount (4) and
then remove the mount and drive carefully from the
machine.
► Loose the 4 screws (1) fastening the conveyor drive
(2). While doing this, carefully unthread the conveyor
drive from the toothed belt (3) and take it off the
mount.
CAUTION
Installation instructions
► Make sure that the toothed belt is positioned accurately in the guidance on the motor shaft.
► While you tighten the screws fastening the conveyor drive, set the tension of the toothed
belt correctly to 250+/-20 Hz.
Service Work
3.6.10 Replacing the Conveyor Drive Toothed Belt [03047677-xx] Conveyor
Service Manual SIPLACE SX4/DX4 113
3.6.10
3.6.10 Replacing the Conveyor Drive Toothed Belt [03047677-xx]
Replacing the Conveyor Drive Toothed Belt [03047677-xx]
Parts, Equipment and Tools
▪ Toothed belt Syncroflex 10 AT3/300 GEN III [03047677-xx]
Overview
Removal
► Dismantle the conveyor drive (see "3.6.9 Replacing the Conveyor Drive [03075892-xx]" [ ➙ 110]).
► Carefully unthread the conveyor drive.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
1. Fastening screws for conveyor drive
2. Conveyor drive
3. Toothed belt for conveyor drive
CAUTION
Installation instructions
► Make sure that the toothed belt is not folded or otherwise damaged.
► While you tighten the screws fastening the conveyor drive, set the tension of the toothed
belt correctly to 250+/-20 Hz.