SIPLACE-SX4-DX4-用户手册 - 第167页
Service Work 3.9.7 Replacing the Cutter Blades Cutter Service Manual SIPLACE SX4/DX4 167 ► Push the spacers (with inserted f eeler gaug es) as far as possible in the direction of th e moveable blade. The maximum per mi s…
Service Work
Cutter 3.9.7 Replacing the Cutter Blades
166 Service Manual SIPLACE SX4/DX4
Installation
► Use an SW10 open-ended wrench to push against the relevant joint (3) and then tighten both screws
(2) to a torque of 6 Nm.
► Fit the two caps over the fastening screws on the movable blade.
► Place the two new spacers (4) to the left and right of the moveable blade. The spacer side marked
with a number must face away from the blade.
► Lubricate the contact/slide surfaces for the moveable blade, as described in the section "Prepara-
tions".
► Insert the dismantled wiper unit (3) and the downholders back in and tighten loosely with the four
hexagon socket-head screws (4).
Cutter (using example of X series)
► Correctly insert the moveable blade (1) into the cutter
and shift it along to its original installation position.
► Apply Loctite no. 243 to the two M4 screws, to fasten
the joint in the moveable blade.
► Insert the screws (2) into the left and right holes, pro-
vided in the moveable blade.
NOTICE!
Make sure that the joint (3) can slide into the slot (= anti-
twist function) in the moveable blade without obstruction.
2
3
4
1
4
3
2
CAUTION
The spacers and blades are matched!
► Do not use any spacers from other sets of blades.
CAUTION
Only apply grease to the exact points required!
The overlapping cutting surfaces may only be greased with Interflon Fin Grease [03020782-xx].
Also observe the preventive maintenance manual for your machine.
Cutter (using example of X series)
► Place a feeler gauge (0.5 - 1.0 mm thickness) on the
left and right, between the spacer and the front of the
moveable blade (1).
► Place the previously removed holding-down device
(2) onto the new spacers.
NOTICE!
Holding-down device
The holding-down devices with function status 03 are de-
signed for use with cutters of function status -04 (= with
tape deflector).
1
2
4
1
5
4
3
2
Service Work
3.9.7 Replacing the Cutter Blades Cutter
Service Manual SIPLACE SX4/DX4 167
► Push the spacers (with inserted feeler gauges) as far as possible in the direction of the moveable
blade. The maximum permissible gap is 1.0 mm.
► Now tighten the four screws (4) crosswise at the downholder.
► Remove the two feeler gauges.
► Insert the new stationary blade (5) in the correct position and screw tight.
Final Work:
If the gap is correct:
► Fit the baffle plate and cover plate. Make sure that the edges are parallel.
► Remove the clamps form the cutter/ remove the cutter from the assembly plate.
► Further installation is performed by following the above instructions in the reverse order.
See also
3.10.1 Replacing the COT Insert Assembly [03080552-xx] [ ➙ 170]
Cutter (using example of X series)
► Use a feeler gauge to check the gap between the
tape deflector (1) and the moveable blade (2), along
the entire length and width of the blade.
⇨ The 0.05 mm feeler gauge should fit through the
gap.
⇨ The 0.25 mm feeler gauge should not fit through
the gap.
If the gap is not correct, check:
▪ Whether the wrong holding-down device has been in-
stalled (with function status < 03)
▪ The holding-down devices are those designed for
cutters with function status -04 (= with tape deflector)
▪ Whether the blades, tape deflector etc. were cleaned
before installation
1
2
CAUTION
Check how the cables are run!
Make sure that the cables and hoses are not pinched or subjected to excess strain.
Service Work
Cutter 3.9.8 Replacing the Used Tape Chute [03067460-xx]
168 Service Manual SIPLACE SX4/DX4
3.9.8
3.9.8 Replacing the Used Tape Chute [03067460-xx]
Replacing the Used Tape Chute [03067460-xx]
Parts, equipment and tools
▪ Use tape chute assembly [03067460-xx]
▪ Allen key set
Overview
SXDX4
1 Waste slide 2 COT insert
3 Manual Table for DX4 4 Fastening screw for used tape chute, left
5 Fastening screw for used tape chute, right