SIPLACE-SX4-DX4-用户手册 - 第197页
Service Work 3.12.8 Replacing the Complete Coupling - Earthing and Comp ressed Air for the Bulk Case Docking Station for X-Series Component T rolley Service Manual SIPLACE SX4/DX4 197 Removal/Installation Individual repl…
Service Work
Docking Station for X-Series Component Trolley 3.12.7 Replacing the Feeder Control Unit (FCU) [03059623-xx]
196 Service Manual SIPLACE SX4/DX4
3.12.7
3.12.7 Replacing the Feeder Control Unit (FCU) [03059623-xx]
Replacing the Feeder Control Unit (FCU) [03059623-xx]
Parts, equipment and tools
▪ X-FCU, X-Series [03059623-xx]
Overview
Removal/installation
Removal and installation is identical to that for the COT insert.
See also
3.10.2 Replacing the Feeder Control Unit (FCU) [03059623-xx] [ ➙ 172]
3.12.8
3.12.8 Replacing the Complete Coupling - Earthing and Compressed Air for the Bulk Case
Replacing the Complete Coupling - Earthing and Compressed Air for the Bulk Case
Parts, Equipment and Tools
You can either replace the individual coupling socket or the complete coupling unit for earthing and com-
pressed air.
▪ Coupling socket for compressed air coupling [03017026-xx]
▪ Coupling assembly for ground and compressed air [03017025-xx]
Overview
1. Feeder Control Unit
1
1. Coupling socket for component trolley compressed
air coupling (bulkcase feeder)
2. Pneumatic connection to pneumatic control valve 5.5
bar
3. Component trolley ground coupling (bulkcase feeder)
3
1
2
Service Work
3.12.8 Replacing the Complete Coupling - Earthing and Compressed Air for the Bulk Case Docking Station for X-Series Component Trolley
Service Manual SIPLACE SX4/DX4 197
Removal/Installation
Individual replacement of coupling socket for compressed air coupling
► Unplug the compressed air connection.
► Use an open-end wrench to unscrew the coupling socket from its mount .
► Screw in the new coupling socket and connect the compressed air supply.
► Switch on the compressed air supply.
► Check the set pressure of 5.5 bar at the pressure control valve (located at the back).
Replacing the complete coupling for earthing and compressed air
► Unplug the compressed air connection.
► Loosen the fastening screw and remove the complete unit.
► Fit the new assembly and reconnect the compressed air supply.
► Switch on the compressed air supply.
► Check the set pressure of 5.5 bar at the pressure control valve (located at the back).
1. Fastening the complete coupling (earthing and com-
pressed air)
2. Coupling socket for compressed air coupling
3. Mount
4. Pneumatic connection to pressure control valve 5.5
bar at the back
CAUTION!
Risk of injury from compressed air!
Risk of injury when disconnecting pressurized com-
pressed air lines.
Switch off the compressed air supply.
3
2
4
1
Service Work
Docking Station for X-Series Component Trolley 3.12.9 Replacing the Unlocking Pushbutton [00334095-XX]
198 Service Manual SIPLACE SX4/DX4
3.12.9
3.12.9 Replacing the Unlocking Pushbutton [00334095-XX]
Replacing the Unlocking Pushbutton [00334095-XX]
Parts, equipment and tools
▪ Unlocking pushbutton [00334095-xx]
Overview
Removal/installation
► Loosen the four screws (5) fastening the cover (3). The cover is clamped in place with the help of
the bar (4).
► Pull the cover (1) out of the docking station.
► Take care not to damage the earth connection.
► Loosen the screw fastening the terminal block (6) of the pushbutton.
► Turn the terminal block and extract it from its fixtures.
► Label the connection leads and disconnect these from the terminal block.
► Connect the connection cables to the new pushbutton.
► Fit the new pushbutton.
► Refit the cover.
► Connect the power pack connection cable and press the ON/OFF button to switch on.
► Check the function of the pushbutton, by trying out the unlocking procedure.
1. Unlocking pushbutton
1
1. ON / OFF switch
2. Power supply plug
3. Cover
4. Bar for clamping the cover
5. Four screws fastening the cover
6. Terminal block for pushbutton
DANGER!
Switch off the voltage supply
Press the ON/OFF button (1) to switch off, and then un-
plug the power supply (2).
4
6
5
1
3
2