SIPLACE-SX4-DX4-用户手册 - 第56页
Service Work Electrical System 3.2.15 Replac ing the Microfuse (F40 to F51) [0 3010626- xx] 56 Service Manual SIPLACE SX4/DX4 3.2.15 3 . 2 . 1 5 R e p la c in g t h e M ic r o f u s e ( F 4 0 t o F 5 1 ) [ 0 3 0 1 0 6 2 …
Service Work
3.2.14 Replacing the SP Splitter (A10) [03076607-xx] Electrical System
Service Manual SIPLACE SX4/DX4 55
3.2.14
3.2.14 Replacing the SP Splitter (A10) [03076607-xx]
Replacing the SP Splitter (A10) [03076607-xx]
Parts, Equipment and Tools
▪ SP splitter [03076607-xx]
▪ 12x microfuse 5x20/T6.3A/ceramic [03010626-xx] (supplied – see machine service box)
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Loosen the screws fastening the mesh cover on the SP splitter and then remove the mesh cover.
► Unplug all electrical connections to the SP splitter. Mark their positions, to make clear assignment
easier later on.
► Loosen the screws fastening the SP splitter and then remove this.
Installation
► Follow the removal instructions in reverse order for installation.
1. SP splitter (A10)
Service Work
Electrical System 3.2.15 Replacing the Microfuse (F40 to F51) [03010626-xx]
56 Service Manual SIPLACE SX4/DX4
3.2.15
3.2.15 Replacing the Microfuse (F40 to F51) [03010626-xx]
Replacing the Microfuse (F40 to F51) [03010626-xx]
Parts, equipment and tools
▪ Microfuse 6.3A T / 150 VDC [03010626-xx]
Overview
Removal
► Use a suitable screwdriver to turn the fuse holder out of its socket.
► Remove the old microfuse from the fuse holder and replace this with a new microfuse of the same
type.
Installation
► Follow the removal instructions in reverse order for installation.
See also
5.2.1 Overview of Electrics [ ➙ 233]
NOTICE
Fuses
A fuse kit for the power supply is included with the delivery of the machine in a separate pack-
age or may be in the power supply.
1. Microfuses F40 to F51
2. LED D40 to D51
The LEDs show the operational readiness of the individ-
ual microfuses.
Voltage Gantry 1 Gantry 2 Gantry 3 Gantry 4
+150V F40 F42 F43 F41
+42V F44 F46 F47 F45
+24V F48 F50 F51 F49
Service Work
3.3.1 Replacing the Control Computer BoxPC Control
Service Manual SIPLACE SX4/DX4 57
3.3
3.3 Control
Control
3.3.1
3.3.1 Replacing the Control Computer BoxPC
Replacing the Control Computer BoxPC
Parts, equipment and tools
▪ SX4: BoxPC 827B, 1 GB RAM [03069632-xx]
▪ DX4: BoxPC 627B with hotlink cable, 2 GB RAM [03055300-xx]
▪ X series S: Control computer BoxPC 827C [03094732-xx] or
Control computer BoxPC 627C [03094731-xx] (as option for 3D coplan)
Overview
CAUTION
Plug-in card
The BoxPC is supplied without the following parts. These must be removed from the old Box
PC and fitted in the new one or ordered as new parts.
► Hotlink interface PCI-A24-K01 (1x, with stationary camera 2x) [03052135-xx]
► CAN card PowerCAN-PCI (1x) [03052590-xx]
► Working memory SO-DIMM DDR2 667 1024MB (1x)
BoxPC 827C (SX4/DX4, X series S)
The BoxPC is located in a rack unit between locations 1
and 2.
1. Power supply
2. Hotlink interface
Depending on the placement heads used, there are
either one or two hotlink interfaces fitted.
One hotlink interface: if only C&P20 heads are fitted.
Two hotlink interfaces: all other placement head con-
figurations
3. LAN connections
4. USB connections
5. CAN card
Example of BoxPC 627B
BoxPC 627C (SX1/SX2/DX1/DX2, 3D coplan)
1. Power supply DC 24 V
2. CAN 1
3. CAN 2
4. Hotlink card
5. LAN connections
6. USB connections
7. DVI/VGA monitor connection