SIPLACE-SX4-DX4-用户手册 - 第69页

Service Work 3.4.7 Replacing the Side Channel Compressor Elmo Blower (Locati on 3) [03004094-xx] Pneumatic System Service Manual SIPLACE SX4/DX4 69 Removal ► Switch off the machine, disconnec t it from the po wer supply …

100%1 / 298
Service Work
Pneumatic System 3.4.6 Buffer Module for Autorecovery Option [03086425-xx]
68 Service Manual SIPLACE SX4/DX4
3.4.6
3.4.6 Buffer Module for Autorecovery Option [03086425-xx]
Buffer Module for Autorecovery Option [03086425-xx]
Parts, equipment and tools
▪ Buffer module DC24V UF20.241 for autorecovery [03086425-xx]
Removal/installation
3.4.7
3.4.7 Replacing the Side Channel Compressor Elmo Blower (Location 3) [03004094-xx]
Replacing the Side Channel Compressor Elmo Blower (Location 3) [03004094-xx]
Parts, equipment and tools
▪ Side channel compressor ELMO blower [03004094-xx]
Overview
NOTICE
See the assembly instructions
For removal and installation information, refer to the "Autorecovery X/SX" assembly instruc-
tions[00196853-xx] (German/English).
CAUTION
Installation instructions
► Seal the compressed air system with sealant. Observe the instructions in section "3.4.2
Sealing the Screwed Connections" [ ➙ 64] in connection with this.
1. Elmo blower electrics
2. Elmo blower
3. Cooling air filter
The ELMO blower is located at location 3, behind the side
cover.
Service Work
3.4.7 Replacing the Side Channel Compressor Elmo Blower (Location 3) [03004094-xx] Pneumatic System
Service Manual SIPLACE SX4/DX4 69
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► To do this, loosen the screws fastening the side cover and remove these. (See "3.4.3 Dismantling
the Lower Side Cover" [ ➙ 64])
► Unplug all electrical and pneumatic connections to the Elmo blower. You may want to mark their po-
sitions, to make clear assignment easier later on.
► Loosen the screws fastening the Elmo blower and then remove it.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
CAUTION!
When working on the pneumatic system, always switch
off the compressed air supply.
► Push the lever (1) for the compressed air supply
back, until it is positioned horizontally.
► Open the screw (2) on the inlet filter to vent the sys-
tem.
► All manometers must be set to zero.
CAUTION
Installation instructions
► Seal the compressed air system with sealant. Observe the instructions in section "3.4.2
Sealing the Screwed Connections" [ ➙ 64] in connection with this.
Service Work
Pneumatic System 3.4.8 Replacing the Electronic Ballast for the ELMO Blower [03006517-xx]
70 Service Manual SIPLACE SX4/DX4
3.4.8
3.4.8 Replacing the Electronic Ballast for the ELMO Blower [03006517-xx]
Replacing the Electronic Ballast for the ELMO Blower [03006517-xx]
Parts, equipment and tools
▪ Electronic ballast for ELMO blower [03006517-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► To do this, loosen the screws fastening the side cover and remove these. (See "3.4.3 Dismantling
the Lower Side Cover" [ ➙ 64])
► Unplug all electrical and pneumatic connections to the Elmo blower electrics. You may want to mark
their positions, to make clear assignment easier later on.
► Loosen the screws fastening the Elmo blower electrics and then remove these electrics.
Installation
► Follow the removal instructions in reverse order for installation.
1. Elmo blower electrics
2. Elmo blower
3. Cooling air filter
The ELMO blower is located at location 3, behind the side
cover.
CAUTION!
When working on the pneumatic system, always switch
off the compressed air supply.
► Push the lever (1) for the compressed air supply
back, until it is positioned horizontally.
► Open the screw (2) on the inlet filter to vent the sys-
tem.
► All manometers must be set to zero.