CX200-4(Maint) - 第213页
Error ID ltem Description 4a0101 Camera X/Y Camera Through Picture Display (Cause 1) Self-Diagnostics Error Message (Remedy 1) Zero all axes and re-start the operation. When the machine cannot be set to its normal condit…
Error ID ltem Description
490501 EB005 Board EB005 board was not detected.
490502 EB005 Board Flash write error
490503 EB005 Board RAM read/write error
490504 EB005 Board Init Flash write error
490505 EB005 Board Flash read/write error
490506 EB005 Board Binary data error
490601 Serial I/O Board Serial I/O Board was not detected.
490701 HLS Satellite HLS Satellite H1 was not detected.
490702 HLS Satellite HLS Satellite H2 was not detected.
490703 HLS Satellite HLS Satellite H3 was not detected.
490704 HLS Satellite HLS Satellite ETC1 was not detected.
490705 HLS Satellite HLS Satellite ETC2 was not detected.
490706 HLS Satellite HLS Satellite F12 was not detected.
490707 HLS Satellite HLS Satellite F34 was not detected.
490708 HLS Satellite HLS Satellite T1 was not detected.
490709 HLS Satellite HLS Satellite XY was not detected.
49070a HLS Satellite HLS Satellite FR was not detected.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
01 10-003 2-123 AFO01ETRP
3.3 Error IDs and Remedial Procedures
Error ID ltem Description
4a0101 Camera X/Y Camera Through Picture Display
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
4a0201 Camera Sensitivity Check Lighting Data Transmission
4a0202 Camera Sensitivity Check Camera Sensitivity
4a0203 Camera Sensitivity Check Display initialization
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
4a0301 Comp Recognition Lighting Comp Recognition Lightingj
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
4a0401 Comp Recognition Camera Lighting Data Transmission
4a0402 Comp Recognition Camera Camera Through Picture Display
4a0403 Comp Recognition Camera Camera Offset
4a0404 Comp Recognition Camera Camera Magnification Data Transmission
4a0405 Comp Recognition Camera Dot Recognition
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
01 10-003 2-124 AFO01ETRP
Error ID ltem Description
4a0501 P.E.C. Camera Camera Magnification Data Execution
4a0502 P.E.C. Camera Magnification Data Transmission
4a0503 P.E.C. Camera Mark Data Transmission
4a0504 P.E.C. Camera Lighting
4a0505 P.E.C. Camera Picture Taking
4a0506 P.E.C. Camera Recognition Execution
4a0507 P.E.C. Camera Camera Through Picture Display
4a0508 P.E.C. Camera Display initialization
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
4b0101 Warning Maintenance The dust box is full of waste chip.(stop count over)
4b0102 Warning Maintenance The component box is full of waste chip.(stop count over)
(Cause 1) Self-Diagnostics Error Message
(Remedy 1)
Remove the cut pieces of the tape and wasted components and re-start the
automatic operation.
4b0301 ILLEGAL OPERATION THE INTERLOCK SW IS CHANGED IN RUN STATE.
(Cause 1) The [OPERATION] switch was changed over by mistake.
(Remedy 1) Change over the [OPERATION] switch to “RUN” and press the [SETUP] button.
Press the [ALL] button (entitled “ZERO”) to zero all axes and re-start the produc-
tion.
01 10-003 2-125 AFO01ETRP
3.3 Error IDs and Remedial Procedures