CX200-4(Maint) - 第271页
Recognition Error ID Item Description 02 ** 2901 ** Picked Posture Error The pick angular skew is big. 02 ** 2902 ** Picked Posture Error The pick-up position has deviated greatly in X direction. 02 ** 2903 ** Picked Pos…
Recognition Error ID Item Description
02 ** 2201 ** Error in Lead Inspection The number of leads is incorrect.
02 ** 2202 ** Error in Lead Inspection The number of leads is small.
02 ** 2203 ** Error in Lead Inspection The number of leads is large.
02 ** 2204 ** Error in Lead Inspection The lead width is incorrect.
02 ** 2205 ** Error in Lead Inspection The lead width is shorter than the tolerance.
02 ** 2206 ** Error in Lead Inspection The lead width is longer than the tolerance.
02 ** 2207 ** Error in Lead Inspection The lead length is incorrect.
02 ** 2208 ** Error in Lead Inspection The lead length is shorter than the tolerance.
02 ** 2209 ** Error in Lead Inspection The lead length is longer than the tolerance.
02 ** 2210 ** Error in Lead Inspection The lead pitch is incorrect.
02 ** 2211 ** Error in Lead Inspection The lead pitch is smaller than the tolerance.
02 ** 2212 ** Error in Lead Inspection The lead pitch is larger than the tolerance.
02 ** 2213 ** Error in Lead Inspection The lead position (LATL DIR) is incorrect.
02 ** 2214 ** Error in Lead Inspection The lead position (LONG DIR) is incorrect.
(Cause 1)The results of the lead inspection differ from the parameters specified in
the component library data for the selected components.
(Remedy 1) Check the leads of the selected component and the component library
data.
Correct wrong parameters if they are set in the component library data.
01 10-003 2-181 AFO01ETRP
4.3 Recognition Error IDs and Remedial Procedures
Recognition Error ID Item Description
02 ** 2901 ** Picked Posture Error The pick angular skew is big.
02 ** 2902 ** Picked Posture Error The pick-up position has deviated greatly in X
direction.
02 ** 2903 ** Picked Posture Error The pick-up position has deviated greatly in Y
direction.
02 ** 2904 ** Picked Posture Error The pick-up position has deviated greately in X
or Y direction.
(Cause 1) When a component is picked up, the pick-up positions (X and Y) and
angle have shifted greatly from the correct ones.
(Cause 2)When the tape is fed, a component is turned vertically.
(Remedy 1) Check the selected component and the tape feeder.
Check if the feeder (B) offset data is correct.
Check if the component library data is correct.
(Remedy 2) Check the selected component and the tape feeder.
01 10-003 2-182 AFO01ETRP
4.3 Recognition Error IDs and Remedial Procedures
Recognition Error ID Item Description
02 ** 3101 ** Error in Corner Detection More than two corners of a component are hid-
den by the protruded nozzle.
02 ** 3102 ** Error in Corner Detection Corner Not Detected.
(Cause 1) The pick-up position has shifted from the specified one in the X direction.
Fig. 4B21
(Cause 2) The tapered part of the vacuum nozzle end or the diffusion plate is stained.
Fig. 4B22
(Remedy 1) Check the component and the tape feeder.
(Remedy 2) Clean the vacuum nozzle end or the diffusion plate.
02 ** 3201 ** Error in Center of Gravity Detection The component shape (size) is not applicable.
02 ** 3202 ** Error in Center of Gravity Detection Failed in Corner Detection.
02 ** 3203 ** Error in Center of Gravity Detection Failed in Center of Gravity Detection.
(Cause 1)The selected component does not match the nozzle.
(Cause 2)The component is bent due to weak vacuum suction forc
(Remedy 1) Check the selected component and the vacuum nozzle.
(Remedy 2) Check the vacuum pressure.
01 10-003 2-183 AFO01ETRP
Component
Vacuum Nozzle
Dirty Spots
4.3 Recognition Error IDs and Remedial Procedures