YS24X_Ope_E - 第144页
3-12 3 Starting and ending pr oduction 4 Pr ess [Y es] when a conirmation dialog box appears. Shutdown confirmation dialog box Press [Y es]. 24307-L4-00 5 Mo ve the machine to the origin position. When the move-to-origin…
3-11
3
Starting and ending production
2. Ending production and turning power off
Use the following procedure to end board production.
1
Stop machine operation.
There are four methods for stopping the machine operation.
e
1. Emergency stop button:
Press this button to trigger emergency stop. Do not use this button in normal operation.
2. [STOP] button (operation panel):
Pressing the [STOP] button stops the machine operation immediately. To resume operation, press the
[START] button on the operation panel.
3. [Cycle Stop] button (operation screen):
Pressing this button stops the machine operation just after components are mounted on the current
board.
4. [Convey-out stop] button (operation screen):
Use this button when you want to end production after completing component mounting on the
boards currently on the conveyor. All boards on the conveyor are carried out after component
mounting, but new boards are not carried in from the upstream side.
c
2
Reset the operation.
Press the [RESET] button on the operation panel. The machine then returns to the board production
standby status.
3
Press the [Off] button.
Press the [Off] button in the left button area of the screen.
[Off] button
[Off] button
24306-L4-10
3-12
3
Starting and ending production
4
Press [Yes] when a conirmation dialog box appears.
Shutdown confirmation dialog box
Press [Yes].
24307-L4-00
5
Move the machine to the origin position.
When the move-to-origin dialog box appears, press [OK].
6
Press the [OK] button when the shutdown confirmation dialog box appears.
e
7
Press the emergency stop button.
When the emergency stop dialog box appears, press the emergency stop button and then press the
[OK] button.
8
Turn off the power switch on the machine.
When the message "Ready to shut down" appears, press the [OK] button and then turn off the power
switch on the lower right of the machine.
c
3-13
3
Starting and ending production
3. Displaying the production monitors
Press the [Monitor] button to confirm the operation status during production.
The mounting information can be confirmed by selecting the [Main], [Detail], [Vision], [Alignment] and [Retry]
tabs.
TIP
When boards are being produced using both lanes of dual-lane machines, the lane select button is displayed on the
[Main], [Detail], [Fiducial] and [Badmark] tabs.
3.1 Production
This screen shows the status of machines currently producing boards. Real-time information is displayed on the
machine layout view as shown below. When an error occurs on the machine, open this screen to check status
information such as what type of error occurred, operating instructions, and warnings, etc. Error locations are
grouped into placement tables, feeders and conveyor units. Locations with errors are shown on the machine
layout view in different colors to make the error location easy to find.
Monitor: Production
1
2
4
3
5
6
Shows the machine rear as a colored background.
24309-L4-00
1. Transfer status area
Displays the conveyor status where an error, operating instruction, or warning involving board transfer was issued.
When a hazard sensor is activated, the board where the error has occurred appears in semi-transparent red on the screen.
When the sensor in the board clamp position or board standby position is activated, the board in the board clamp
position or board standby position appears in semi-transparent green on the screen.
2. Feeder status area
Displays the feeder at the feeder set position where parts are registered, by referencing "Parts" - "Feeder Set No." of the
board data currently used for board production. Nothing is displayed at feeder set positions where no parts are registered.
3. Feeder plate status area
Displays "OK" when there are no errors, operating instructions or warnings for the feeders currently in use.
Displays "n Parts" ("n" is the number of feeders) when errors, operating instructions or warnings were issued for the
feeders currently in use.