YS24X_Ope_E - 第163页
A-1 Appendix A1. Specifications n YS24X specifications Item Specifications Operating ambient temperature Function guaranteed: 15 to 35°C Accuracy guaranteed: 20 to 28°C Operating ambient humidity 20 to 90% (no condensati…
A-1
Appendix
A1. Specifications
n
YS24X specifications
Item Specifications
Operating ambient temperature
Function guaranteed: 15 to 35°C
Accuracy guaranteed: 20 to 28°C
Operating ambient humidity 20 to 90% (no condensation), optimal range: 50 to 60%
Noise level Under 78dB
Power requirement (voltage and frequency) 3-phase AC 200/208/220/240/380/400/416 V ± 10%, 50/60 Hz
Average power consumption 2.0kW
Power cable (conductor cross-section area) 5.5 mm
2
or more
Overvoltage category *
1
Category III
Pollution degree *
1
Degree 2
Supply air pressure *
2
0.45MPa
Air flow rate *
6
260 Nl/min., Instantaneous maximum flow rate: 420 Nl/min.
Board transport height *
3
900 mm ± 10 mm
Data
Number of mounting points *
4
10,000 points
Number of part types 255 types per board
Number of fiducial marks *
5
128 sets per board
*1: Conforms to IEC60664-1.
*2: Clean, dry air passed through an air dryer and filter.
*3: Distance from the floor surface to the upper surface of conveyor belt.
*4: Decreases with the number of boards, blocks and fiducial marks.
*5: When using 2-point fiducial mode.
*6: Shows the standard air flow rate of the machine with the tape cutter. (This includes an air flow rate of 10 Nl for tape
cutter.)
c
Conveyor's board sensors may fail to detect a production board if it has a slit or cutout.
n
NOTE
For more detailed information not listed above, please refer to specification sheets.
S-1
Index
A
Alarm buzzer 1-2
Axis configuration 1-22
Blow station 1-25
Board clamping method 2-25
Board production
Ending production 3-11
Pre-operation check 2-20
Resuming operation 3-6
Starting production 3-1
Starting the machine 2-21
C
CE marking i
Component supply section 1-13
Connection between machines 1-2
Conveyor unit 1-19
Conveyor unit setup 2-25
Conveyor width 2-14
[Convey-out stop] button 3-11
[Cycle Stop] button 3-11
Data input unit 1-3
dual-lane 2-28
dual-stage 2-27
Dummy feeder iv
E
Emergency stop
Canceling emergency stop 2-1
Error
Clearing an error 2-2
Errors and troubleshooting 2-3
Feeder exchange carriage 1-16
Feeder plate 1-13
Air connector 1-13
Power supply connector 1-13
[Feeder Setting] button 2-17
Feeder setup section 1-13
H
Head assembly 1-5
10-in-line multi-head assembly 1-6
K
Keyboard 1-3
Machine main unit 1-1
Names and functions of major parts 1-1
Manual feeder operation 2-17
Manual head operation 2-16
Manual I/O operation 2-18
[Monitor] button 3-13
Mouse 1-3
Multi-vision camera 1-6
N
Nozzle shaft blow 1-26
Nozzle station 1-9
Nozzle types 1-7
Narrow adjacent type 1-8
Standard type 1-7
Operation panel 1-3
[READY] button 2-1
Operation panel buttons 1-4
[ACTIVE] button 1-4
[EMERGENCY STOP] button 1-4
[ERROR CLEAR] button 1-4
[READY] button 1-4
[RESET] button 1-4
[START] button 1-4
[STOP] button 1-4
Operation screen 2-8
Menu button area 2-8
Status area 2-8
Operation speed 3-3
[Operator] button 2-22
P
Pallet indicator 1-18
Password 2-22
Pick Rate Warning 3-27
Pickup position offset 3-25
Power switch 1-2,2-21
Turning power off 3-11
Pressure gauge 1-2
Production monitors 3-13
Push-up pin 2-27
Q
QFP dump station 1-34
R
Recovery pallet 1-35
Return-to-origin 2-21
S
Safety ii
Safety cover 1-2
Safety message vii
sATS 1-17
Setup screen 2-11,3-2
[Check Nozzles] button 3-3
[Feed Bulk] button 3-3
[Required Nozzles] button 3-3
[Required Parts] button 3-2
Signal light 1-2
Specifications A-1
T
Tape cutter 1-31
Tape feeder
Disposing of used top tape 3-4
Operation check 2-54
Setting a tape feed pitch 2-34
Settings on the mounter side 2-49
Setting the tape 2-29
Tray changer 2-43
U
Unit screen 2-13
W
Warm-up 2-23
[Warm Up] button 2-23
Warning labels xi
"watch-and-wait" mode 3-29