YS24X_Ope_E - 第30页
3 9.1 Coplanarity checker 1-3 3 4 9.3 Recovery pallet 1-3 5 Chapter 2 Basic operation 1 1.1 Canceling emergency stop 2- 1 1.2 Clearing an err…
General Contents
About this manual
1. Using this manual i
1.1 Available manuals i
i
2. Contents of each chapter iii
3. Page layout iv
Chapter 1 Part names and functions
1
3
2.1 Keyboard and mouse 1-3
4
3. Head assembly 1-5
3.1 Component pick-and-place head 1-6
3.1.1 10-in-line multi-head assembly 1-6
3.1.2 Multi-vision camera 1-6
3.2 Nozzle types 1-7
3.2.1 Nozzles for the 10-in-line head assemblies 1-7
9
4. Component supply section 1-13
4.1 Supplying components from feeder plates 1-13
4.1.1 Fixed feeder plates 1-13
4.1.2 Feeder exchange carriage 1-16
4.2 Supplying components from tray changer (sATS
II
7
5.
Conveyor unit 1-19
5.1
Conveyor unit 1-19
5.2 Sensor layout of conveyor unit 1-20
6. Axis configuration 1-22
5
7.1 Performing a nozzle shaft blow 1-26
1
8.1 Tape cutting during component mounting 1-31
8.2 Tape cutting during board conveying 1-32
2
EPL4127120
3
9.1 Coplanarity checker 1-33
4
9.3 Recovery pallet 1-35
Chapter 2 Basic operation
1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
8
8
2.2 Setup screen 2-11
2.3 Unit screen 2-13
3. Starting and stopping the machine 2-19
3.1 Pre-operation check 2-20
3.2 Starting the machine 2-21
3.3 Warming up the machine 2-23
5
3.4.1 Conveyor unit setup flow 2-26
4. Preparing the component supply unit 2-29
4.1 Tape feeders 2-29
4.1.1 Setting the tape 2-29
4.1.2 Setting a tape feed pitch 2-34
4.1.3 Installation on a mounter 2-38
4.2 Wide multi-stick feeder 2-39
4.2.1 Installation of tracks and sticks 2-39
4.2.2 Installation on a mounter 2-42
4.3 Tray changer (sATS
II
3
4.3.1 Setting the component trays in the pallet 2-44
4.3.2. Setting the pallet in the magazine 2-45
4.3.3 Replacing a magazine or pallets 2-47
5. Settings on the mounter side 2-49
5.1 Setting the "Package" parameter. 2-49
4
Chapter 3 Starting and ending production
1. Starting production 3-1
1.1 Resuming operation from the stopped point 3-6
1.1.1 Loading the saved data 3-7
1.1.2 Editing mount flags 3-7
1.2 Using the "block skip function" 3-8
1.2.1 Selecting the blocks 3-9
1.2.2 Starting operation 3-10
2. Ending production and turning power off 3-11
3
3.1 Production 3-13
5
7
9
3.5 Alignment 3-21
3.6 Retry 3-22
3
4
5
3.10 Pick Rate Warning 3-27
Appendix
A1. Specifications A-1
Index