Printer 600 Machine Programming - 第104页
0$&+,1( 352*5$00 ,1* 0(183$5$ 0(7(56 1.104 User Manual Software Ve rsion 07SP04 NOTE With e nabled se lected the p arameter Paste While Clean i s removed. Alternate Dis p This parame ter gives the optio n to di spe…
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 07SP04 User Manual 1.103
the end of the under screen cleaner stroke. Options are:
Print Deposits This parameter sets the number of consecutive print strokes carried out on one
substrate.
Print Vacuum
Mode
This parameter determines the state of the vacuum during the print and flood
stages of the cycle. The parameter is only available if Adhesive has been
selected in the Print Mode parameter.
Paste Dispense
Rate
This parameter sets the number of print cycles which occur between cycling of
the paste dispense system.
Paste Dispense
Speed
This parameter sets the speed at which the paste dispenser moves across the
stencil thereby determining the amount of paste deposited on the stencil.
Paste While Clean This parameter enables the machine to carry out a paste dispense while
cleaning the stencil. Available modes are:
Paste With Board This parameter gives the option to dispense paste with a board loaded and held
at print height. This prevents paste dropping through the image on the stencil,
options are:
Option Default
Disabled Disabled
Enabled
Select Default
11
2
3
Mode
ON
OFF
Minimum Maximum Increment
0 (Dispenser switched off) 100 1
Minimum Maximum Increment
10.0mm/sec 100.0mm/sec 1.0mm/sec
Mode
Disabled
Mode 1
Mode 2
Both Modes
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.104 User Manual Software Version 07SP04
NOTE
With enabled selected the parameter Paste While Clean is removed.
Alternate Disp This parameter gives the option to dispense at either ENDS or CENTRE. ENDS
dispenses at the outer 25% of the squeegees. CENTRE dispenses along an
area of 25% either side of the centre line.
Alternate Disp
Rate
This parameter enables the user to select the ratio of alternate dispenses to
standard dispenses.
Paste Recovery
Rate
This parameter sets the frequency, measured in print strokes completed in
either direction, at which paste roll recovery occurs in both directions, when
using squeegees.
Front Paste
Recovery
This parameter sets the extent of paste roll recovery movement while beginning
the rearward print stroke. The movement is measured forward from the print
stroke start position.
Rear Paste
Recovery
This parameter sets the extent of paste roll recovery movement while beginning
the forward print stroke. The movement is measured rearward from the print
stroke start position.
Screen Clean
Mode 1 (including
Vacuum)
This parameter sets the mode of operation of the screen cleaner for the first
clean mode. When selected this parameter opens a window that allows a
screen clean option sequence to be chosen. The sequence includes six stages,
Options Available
Enabled
Disabled
Options Available
Ends
Centre
No Alternate Dispense Every Dispense Every Second Dispense etc.
Minimum Maximum Increment Default
0
(This disables paste
roll recovery)
500 1 1
Minimum Maximum Increment Default
0.0mm 15.0mm
(Subject to front turn-
around envelope)
1.0mm 5.0mm
Minimum Maximum Increment Default
0.0mm 15.0mm
(Subject to rear turn-
around envelope)
1.0mm 5.0mm
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 07SP04 User Manual 1.105
each of which may be one of the following cleaning operations:
Screen Clean
Rate 1
This parameter sets the number of print cycles between the cycling of the
screen cleaner for the first screen clean rate.
Screen Clean
Mode 2 (including
Vacuum)
This parameter sets the mode of operation of the screen cleaner for the second
clean mode. When selected this parameter opens a window that allows a
screen clean option sequence to be chosen. The sequence includes six stages,
each of which may be one of the following cleaning operations:
Screen Clean
Rate 2
This parameter sets the number of print cycles between the cycling of the
screen cleaner for the second screen clean rate.
Vacuum Clean
Start Time
This parameter sets the time in seconds the vacuum is applied for before the
screen clean stroke begins.
NOTE
This parameter is only displayed with a Blue USC fitted and the Under Screen
Cleaner parameter in Set Preferences set to Vacuum.
Clean After
Downtime
This function provides the facility for the stencil to be cleaned automatically with
a preprogrammed clean after a preprogrammed idle time. Clean After Down-
time only becomes active after the machine has performed at least one print
after it is powered up. When selected this parameter opens a window that
allows a clean after knead option sequence to be chosen. The sequence
includes six stages, each of which may be one of the following cleaning
Cleaning Operation Note
Wet A warning is given if the end stroke is wet.
Dry
Vac
None
Minimum Maximum Increment
0 (Screen Cleaner off) 200 1
Cleaning Operation Note
Wet A warning is given if the end stroke is wet.
Dry
Vac
None
Minimum Maximum Increment
0 (Screen Cleaner off) 200 1
Minimum Maximum Increment Default
0.0 sec 5.0 secs 0.5 sec 1.0 secs