00198505-01_SM_SIPLACE_SmartFeeder_EN - 第110页
7 Repairs to SmartFeeder 8 mm X 7.9 Rocker 110 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 7.9.1 Removing the rocker assembly ► Carefully place the feeder module with the right side down on a stable, level an…
7 Repairs to SmartFeeder 8 mm X
7.9 Rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 109
7.8.2.4 Replacing the rocker bearing unit
► Loosen the foil rocker unit (see 7.8.1.1 "Removing the Foil Rocker Assembly" [}104]).
► Remove the foil rocker and the pressure spring (see7.8.2.1 "Replacing the foil rocker, axis and
pressure spring" [}106]).
► Remove the light barrier transmitter (see 7.8.2.3 "Replacing the light barrier transmit-
ter" [}108]).
The rocker bearing unit has now been isolated and can be replaced.
► Fasten the light barrier transmitter to the new rocker bearing unit (see 7.8.2.3 "Replacing the
light barrier transmitter" [}108]).
► Fasten the foil rocker (see 7.8.2.1 "Replacing the foil rocker, axis and pressure
spring" [}106]).
► Fasten the foil rocker unit (see 7.8.1.2 "Fitting the Foil Rocker Assembly" [}105]).
7.9 Rocker
Required spare part
Fig.33: Rocker for foil disposal assy. X8Smart
Feeder module Item no. Designation
SmartFeeder 8mm X 03104247-xx Rocker for foil disposal assy. X8Smart
03096391-xx Pressure spring 0.63x6.4x33.0mm
03122867-xx Bearing shaft, bronze, tamp wheel rocker X4Smart
Required tools
●
Flat-bladed screwdriver size 1
7 Repairs to SmartFeeder 8 mm X
7.9 Rocker
110 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
7.9.1 Removing the rocker assembly
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Use a size 1 slotted screwdriver to loosen the
bearing shaft (1) belonging to the rocker.
► Gently press the rocker backwards, against the
spring tension.
► Pull the bearing shaft completely out of the
rocker.
► Relax the spring, by letting the rocker slowly rise
up again.
► Lift the rocker up and out of the feeder module.
► Remove the spring (2).
7.9.2 Fitting the rocker assembly
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Insert the spring(1) into the base of the feeder
module.
► Fit the rocker(2) onto the spring.
► Press the rocker over the rocker holder(3).
7 Repairs to SmartFeeder 8 mm X
7.10 Tamp wheel
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 111
► Press the rocker into the spring (4).
► Move the rocker until you can completely see the
drilled hole for the rocker holder through the
drilled hole for the rocker itself(3).
► Push the bearing shaft(5) into the drilled hole,
with the thread first.
► Fasten the bearing shaft hand-tight with a size 1
slotted screwdriver.
7.10 Tamp wheel
Required spare part
Fig.34: Knurled tamp wheel assy.
Feeder module Item no. Designation
SmartFeeder 8mm X 03102274-xx Knurled tamp wheel assy. X8Smart
Required tools
●
Phillips screwdriver, small
●
Flat-bladed screwdriver
●
Allen key size 4
●
Tweezers