00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第174页
8 Repairs to SmartFeeder 2x8 mm X 8.12 Flap Tape Disposal 174 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 8.12 Flap Tape Disposal Required spare part Fig.59: Foil disposal flap Feeder module Item no. Designa…
8 Repairs to SmartFeeder 2x8 mm X
8.11 Stripper
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 173
8.10.4 Fitting the knurled tamp wheel right
► Clean the shaft and circlip with Polyhub Gly 801.
► Replace the small spacer.(1)
► Fit the knurled tamp wheel. (2)
► Replace the circlip.(3)
► Replace the washer.(4)
► Remove the toothed wheel 4 tape (see Fitting the
Gear Wheel 4 Foil right).
► Reinsert the stripping device (see 8.11.2 "Fitting
the wiper" [}173]).
► Reinsert the rocker (see 8.8.1.2 "Fitting the Foil
Rocker Cpl." [}165]).
► Refit the left and right side covers (see 8.3.2 "Fit-
ting the Left Side Cover" [}136], 8.3.4 "Fitting the
Right Side Cover" [}137]).
8.11 Stripper
Required spare part
Fig.58: Wiper
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03059930Sxx Wiper
Required tools
●
Phillips screwdriver
●
Flat-bladed screwdriver
8.11.1 Removing the wiper
► Place the feeder on a stable, level and clean sur-
face.
► Remove the right side cover (see 8.3.3 "Remov-
ing the Right Side Cover" [}136]).
► Remove the foil rocker (see 8.8.1.1 "Removing
the Foil Rocker Cpl." [}165]).
► Loosen and remove the marked screw. (1)
► Remove the stripping device.
8.11.2 Fitting the wiper
► Fit the new stripping device. Ensure the knurled tamp wheel does not touch the stripping
device and fasten the screw.
► Refit the foil rocker (see 8.8.1.2 "Fitting the Foil Rocker Cpl." [}165]).
► Fit the right side cover (see 8.3.4 "Fitting the Right Side Cover" [}137]).
8 Repairs to SmartFeeder 2x8 mm X
8.12 Flap Tape Disposal
174 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
8.12 Flap Tape Disposal
Required spare part
Fig.59: Foil disposal flap
Feeder module Item no. Designation
SmartFeeder 2x8mmX 03072467-xx Foil disposal flap /X2x8
03067306-xx Bearing bolt left flap /X2x8
03067320-xx Bearing bolt right flap /X2x8
Required tools
●
Hexagon socket-head wrench
●
TORX screwdriver size T8
●
Phillips screwdriver
8.12.1 Removing the Flap Tape Disposal
► Place the feeder on a stable, level and clean sur-
face.
► Open the flap.
► Remove the marked screwed axle. Hold the
screw on the other side tight while doing so.(1)
► Carefully remove the flap from the feeder mod-
ule.
8.12.2 Fitting the Flap Tape Disposal
► Carefully insert the flap, from the side, into the foil container.
► Tighten the screwed axle.(1)
► Close the flap.
8 Repairs to SmartFeeder 2x8 mm X
8.13 Foil disposal blade
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 175
8.13 Foil disposal blade
Required spare part
Fig.60: Blade partition wall
Feeder module Item no. Designation
SmartFeeder 2x8mmX 00341370Sxx Blade partition wall
NOTICE
Pay attention when preparing the individual blades. Individual blades must be broken at the
cutter edge. Ensure all safety precautions are observed.
Required tools
●
TORX screwdriver 0.6Nm, size T8
WARNING
Risk of injury
The edge of the blade is very sharp. Make sure that you always use a pair of tweezers
when removing and fitting the blade.
8.13.1 Removing the Blade Partition Wall
► Place the feeder on a stable, level and clean surface.
► Open the flap.
► Loosen the screw fastening the blade and remove the old blade.
8.13.2 Fitting the Blade Partition Wall
► Place the new blade in position and tighten the screw.
CAUTION
► The blades are sharp, take necessary safety precautions.