00198505-01_SM_SIPLACE_SmartFeeder_EN - 第255页
10 Repairs to SmartFeeder 24 - 104 mm X 10.7 Drives and gears Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 255 ► Carefully place the feeder module down on its left side. ► Remove the circlip (1) on shifted ge…
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
254 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.7.3 Tape drive (hybrid stepping motor)
Required spare part
Fig.91: Tape drive hybrid stepping motor assembly
Feeder module Item no. Designation
SmartFeeder 24 - 104 mm X 03116587-xx Hybrid stepping motor assembly X24-104Smart
Required tools
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
●
Gauge for tape drive motor X24-104, item no. 03130748-xx
●
Circlip pliers for outer rings 3-10 mm
●
Tweezers
10.7.3.1 Removing the tape drive
► Remove the right side cover (see 10.3.2 "Remov-
ing/fitting the right front cover" [}231])
► Remove the left side plate (see 10.3.1 "Remov-
ing/fitting the left side plate" [}230]).
► Carefully place the feeder module on its right
side.
► Unplug the connector for the tape drive cable
from the connection on the control board.(1)
► Guide the tape drive cable through the marked
opening(2) to the other side of the feeder mod-
ule.
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 255
► Carefully place the feeder module down on its left
side.
► Remove the circlip(1) on shifted gear1.
► Remove the washer (2) on shifted gear1
► Remove shifted gear 1.(3)
► Remove the two screws which fasten the tape
drive.(4)
► Remove the tape drive.
10.7.3.2 Fitting the tape drive
► Carefully place the feeder module down on its left
side.
► Insert the tape drive into the recess.
Make sure that the tape drive cable is on the left
side.
► Run the cable in the cable duct.(1)
► Position the tape drive so that you can see the
holes in the feeder module base unit through the
holes in the drive frame.(2)
► Fit the gauge as shown, with the level side point-
ing upwards, onto the pinion of the tape drive and
onto the axis of shifted gear1.(3)
► Position the tape drive so that the pinion and
gauge can not catch in one another.
► Fix the tape drive with the two Phillips screws
ISO 7045 M2.5x8. Use a Phillips screwdriver with
0.9Nm for this.
► Remove the gauge.
► Fit shifted gear1 with the smaller toothed wheel
pointing downwards onto the axis.(1)
Make sure that the smaller toothed wheel en-
gages below with shifted gear2(2).
The large toothed wheel for the shifted gear will
engage above with the tape drive pinion.(3)
► Fit the washer into place.(4)
► Secure shifted gear 1 with a new circlip.(5)
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
256 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
► Guide the tape drive cable through the marked
opening to the other side of the feeder module.
(1)
Make sure that the cable is on the right side of
the feeder module in the cable duct.
► Carefully place the feeder module on its right
side.
► Press the connector of the tape drive cable into
the marked connection on the control board.(2)
► Fasten the left and the right side covers (see .
(see 10.3.1 "Removing/fitting the left side
plate" [}230] and 10.3.2 "Removing/fitting the
right front cover" [}231]).
10.7.4 Foil drive (hybrid stepping motor)
Required spare part
Fig.92: Foil disposal drive for hybrid stepping motor assembly
Feeder module Item no. Designation
SmartFeeder 24 – 104 mm X 03116587Sxx Hybrid stepping motor assembly X24-104Smart
Required tools
●
Phillips screwdriver 0.6Nm
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
●
Gauge for foil disposal motor X24-104, item no. 03130747-xx
●
Circlip pliers for outer rings 3-10 mm
●
Tweezers