00198505-01_SM_SIPLACE_SmartFeeder_EN - 第281页
10 Repairs to SmartFeeder 24 - 104 mm X 10.13 Handle assembly with control panel Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 281 ► Carefully place the feeder module with the left side down on a stable, level …
10 Repairs to SmartFeeder 24 - 104 mm X
10.13 Handle assembly with control panel
280 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Remove the four screws marked in the diagram,
which are fastening the handle. Use a size T8
TORX screwdriver for this.
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Open the tape container flap.(1)
► Lift the handle straight up and out of the feeder
module base unit. (2)
10.13.2 Fitting the handle assembly
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Open the flap on the foil container.(1)
► Insert the handle straight down and into the
feeder module base unit. (2)
► Close the flap on the foil container.
10 Repairs to SmartFeeder 24 - 104 mm X
10.13 Handle assembly with control panel
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 281
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Fasten the handle using the four marked (see
diagram) screws. Use a TORX screwdriver and
0.6 Nm for this.
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Run the cable as shown.
When running the cable, make sure that the blue
side points upwards at the end of the cable..
► Insert the end of the flat ribbon cable (with the
blue side pointing upwards) up to the stop in the
flat ribbon connection shown on the control
board.(1)
► Close the connection and make sure that the
cable it firmly fitted.(2)
► Fix the left side plate into place. (see 10.3.1 "Removing/fitting the left side plate" [}230]).
► Carefully place the feeder module with the right side down on a stable, level and clean sur-
face.
► Insert the pressure spring into the rocker (see 10.9.2.1 "Replacing the pressure spring and
spring support" [}271]).
► Fasten the right rear side wall (see 10.3.3 "Rear side wall on the right" [}231])
10 Repairs to SmartFeeder 24 - 104 mm X
10.13 Handle assembly with control panel
282 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
10.13.3 Replacing spare parts on the handle
Required spare parts
Fig.103: Control panel, board and control panel window
Feeder module Pos Item no. Designation
SmartFeeder 24–104 mm X 1 03110042-xx Control panel assy. X24-104
2 03110763-xx PCB control panel placed X24-104
3 03110496-xx Window for control panel
4 03116164-xx Window control panel black X24-104
5 03063592-xx Cable control panel X2x8
Required tools
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver size T8, 0.6Nm
10.13.3.1 Removing the control panel, board and window for the control panel
► Carefully place the feeder module with the right side down on a stable, level and clean sur-
face.
► Remove the left side plate (see 10.3.1 "Removing/fitting the left side plate" [}230]).
► Release the removal handle lock.(1)
► Remove the two screws marked in the diagram.
Use a size T8 TORX screwdriver for this.
► Lift the cover plate a little to the side, to give you
access to the parts below.