00198505-01_SM_SIPLACE_SmartFeeder_EN - 第50页
6 Repairs to SmartFeeder 4 mm X 6.8 Foil rocker 50 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 6.8.2 Replacing individual foil rocker parts Fig.11: Individual foil rocker parts Feeder module Position Item no…
6 Repairs to SmartFeeder 4 mm X
6.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 49
6.8.1.2 Fitting the Foil Rocker Assembly
► Turn the foil rocker into the position shown in the
diagram.
► If this is not open, swing the bracket on the flat
ribbon connection(2) upwards.
► Push the flat ribbon cable(1), with the blue side
pointing upwards, into the flat ribbon cable con-
nection(2), as far as the stop.
► Make sure that the flat ribbon cable contacts lie
against the contacts on the connection.
► Swing the bracket on the flat ribbon connection
down(2).
► Carefully place the foil rocker unit(3) onto the
marked fixture holes.
Make sure that the cable(4) slides into the duct well
during insertion and is not bent. If there are any prob-
lems with this, open the left side cover of the feeder
module.
► Very carefully fasten the foil rocker unit with the
two marked TORX screws hand-tight. Use a size
8 TORX screwdriver for this.
6 Repairs to SmartFeeder 4 mm X
6.8 Foil rocker
50 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
6.8.2 Replacing individual foil rocker parts
Fig.11: Individual foil rocker parts
Feeder module Position Item no. Designation
SmartFeeder 4mm X 1 03100349-xx Rocker bearing X8Smart
2 03103850-xx Axis foil rocker X8Smart
3 03101473-xx Foil rocker X8Smart
4 03067456-xx Roller axis for rocker/X2x8
5 03003143-xx Roller /foil disposal X8
6 03120008-xx Pressure spring 0.5x4.0x27.0-EN 10270-1-
DH
7 03033796-xx RF-SN75-2.5 x 6-9.8
8 03100381-xx Light barrier transmitter flat assy. X8Smart
Required tools
●
Screwdriver, size 0
●
Tweezers or flat pliers
6.8.2.1 Replacing the foil rocker, axis and pressure spring
Removing individual parts
► Insert a small flat-bladed screwdriver size 0 into
the small slits on the left and right and press
slightly outwards, to open the long retaining
plates in the rocker bearings and to release the
axis from its holder(1).
► Pull the rocker up and out of the rocker bear-
ings.(2)
6 Repairs to SmartFeeder 4 mm X
6.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 51
► Push the axis sideways out of the foil rocker.(3)
► Pull the pressure spring up and off the pin.(4)
The foil rocker has now been dismantled and defective parts can be replaced.
Fitting individual parts
► Insert the axis into the foil rocker.(1)
► Push the foil rocker axis from above, through the
little slits on the left and right, into the retaining
plates of the rocker bearings, as far as the
stop.(2)
Make sure that the axis of the foil rockers en-
gages on the fixing brackets on the left and right.
► Insert the end of the pressure spring into the pins
on the underside of the foil rocker.(3)
► Insert the other end of the pressure spring into
the pins on the rocker bearings.(4)