00193786-01 - 第114页

SIPLACE GEM SW Version GEM 505.01 HOST Interface Manual Page 114 of 236 ©Siemens AG, all rights reserved 4.7.11 S5F73 - Alarm Report Block Acknowledge S 5 F 7 3 [ W ] * H < - E <L [3] <U4 ALID> * ALID - Alarm…

SIPLACE GEM SW Version GEM 505.01

HOST Interface Manual

4.7.9 S5F71 - Alarm Report Block Send

S5F71 [W] * H<-E

<L [2]

<U1 0> * ALPY Alarm Priority

<L [1]

<L [4]

<U4 ALID> * ALID - Alarm ID

<BOOLEAN ASTAT> * T = Alarm On

F = Alarm Off

<U4 ASER> * ASER Alarm Serial Number

<A [16] 'YYYYMMDDhhmmsscc'> * CLOCK

> .

Note: This message is provided only for compatibility with Host computers which support

an older version of GEM.

If the Equipment Constant "ConfigAlarms" is set to "1", the Equipment sends S5F71

instead of the normal S5F1 Alarm Notification Send.

The SIPLACE reports that an alarm condition has changed.

ALID identifies the Alarm.

ASTAT value is "True" (Non-zero) if this alarm is currently On (Unsafe), or "False" (Zero)

if it is currently Off (Safe).

ASER (Alarm Serial Number) is assigned by the Equipment. Its value begins at "1" and

is incremented by 1 for each alarm reported.

ALPY (Alarm Priority) is always zero.

CLOCK indicates the date and time of the alarm change.

Equipment Constant "Wbits5" controls whether the Equipment sends S5F71 with w-bit =

"1" (Reply Expected) or "0" (No Reply Expected).

4.7.10 S5F72 - Alarm Report Block Acknowledge

S5F72 * H->E

<L> .

The Host acknowledges Alarm Report. This Equipment ignores the data portion of

S5F72.

SIPLACE GEM SW Version GEM 505.01 HOST Interface Manual

4.7.11 S5F73 - Alarm Report Block Acknowledge

S5F73 [W] * H<-E

<L [3]

<U4 ALID> * ALID - Alarm ID

<BOOLEAN ASTAT> * T = Alarm On,

F = Alarm Off.

<A [16] 'YYYYMMDDhhmmsscc'> * TIMESTAMP

> .

Note: This message is provided only for compatibility with older Host computers which

support GEM 3.1.

In order for this message to be used, the Equipment Constant "ConfigAlarms" must be

set to "2".

The SIPLACE reports that an alarm condition has changed.

ALID identifies the Alarm.

ASTAT value is "True" (Non-zero) if this alarm is currently On (Unsafe), or "False" (Zero)

if it is currently Off (Safe).

TIMESTAMP indicates the date and time of the alarm change.

Equipment Constant "WBitS5" controls whether the Equipment sends S5F73 with W-Bit

"1" (Reply Expected) or "0" (No Reply Expected).

4.7.12 S5F74 - Alarm Notification Acknowledge

S5F74 * H->E

<B [1] ACK5> .

The Host acknowledges Alarm Report. This Equipment ignores ACKC5.

SIPLACE GEM SW Version GEM 505.01

HOST Interface Manual

4.8 Stream 6

4.8.1 S6F1 - Trace Data Send

S6F1 [W] * H<-E

<L [4]

<U4 TRID> * Trace ID

<U4 SMPLN> * Sample Number

<A 'yyyymmddhhmmss'> * STIME - Sample Date and Time

<V> * Variable Value

...

> .

The Equipment sends time driven trace data, as previously requested by the Host using

S2F23.

TRID is the Trace ID as initiated by the Host.

SMPLN is the sample number. The first sample is "1", the next "2", and so on. If

REPGSZ is greater than 1, SMPLN is the number of the last sample contained in this

S6F1.

STIME is the date and time at which this sample was taken. If REPGSZ is greater than

1, STIME is the date and time of the last sample contained in this S6F1.

The V's appear in the same order they were specified in S2F23.

S6F1 is normally single block. However, if the Host erroneously initiates a multiblock

trace using an incorrect S2F23, S6F1 may be multi-block. The Equipment never sends

an Inquire/Grant message preceding S6F1.

Equipment Constant "WBitS6" controls whether the Equipment sends S6F1 with W-Bit

"1" (Reply Expected) or "0" (No Reply Expected).

4.8.2 S6F2 - Trace Data Acknowledge

S6F2 * H->E

<B [1] 00> . * ACKC6

The Host acknowledges the data. The Equipment ignores ACKC6.

4.8.3 S6F3 - Annotated Event Report

S6F3 [W] * H<-E, Multiblock

<L [3]

<U4 DATAID> * DATAID

<U4 CEID> * Collection Event ID

<L [2]

<U4 DSID> * DSID=RPTID Report ID