00193437-03_AI_PowerSupplyConversion_DE EN - 第168页

3 Converting the power supply on HF machines A ssembly Instructions, Converting the Power Supply 3.6 Converting the power supply from 3 x 208 VAC to 3 x 400 VAC 12/2013 Edition 166 3.5.8 Inst alling the power supply unit…

Assembly Instructions, Converting the Power Supply 3 Converting the power supply on HF machines

12/2013 Edition 3.5 Converting the power supply from 3 x 400 VAC to 3 x 208 VAC

165

3.5.7 Configuring the inrush current limiter board

The inrush current limitation must be configured in relation to the supply voltage. This is done us-

ing plug-in jumpers on the inrush current limitation board (item 1 in Fig. 3 - 12

Fig. 3 - 12 Configuring the EST inrush current limiter board

(1) Inrush current limitation board

(2) Cover

X1, X2, X3 Connectors for configuring the inrush current limitation

 Remove the cover.

 Remove the jumper plugs from connectors X1, X2 and X3.

 Plug in the jumper plugs one position lower on connectors X1, X2 and X3 (see Fig. 3 - 12).

 Fit the cover (see item 2 in Fig. 3 - 12).

3 x 380 VAC

3 x 400 VAC

3 x 415 VAC

3 x 208 VAC

3 x 230 VAC

3 Converting the power supply on HF machines Assembly Instructions, Converting the Power Supply

3.6 Converting the power supply from 3 x 208 VAC to 3 x 400 VAC 12/2013 Edition

166

3.5.8 Installing the power supply unit

 Carefully push the power supply unit into the housing until it reaches the stop.

 Use the M8 hexagon socket-head screw to secure the unit at the bottom.

 Check that the yellow-green PE wire is connected to the cover.

 Attach the holding cord to the eye in the cover.

 Attach the cover.

PLEASE NOTE: 3

Make sure that the actuating shaft of the main switch slides easily into the opening in the ro-

tary button. 3

 Use the machine key to lock the cover.

3.5.9 Carry out the safety check to DIN EN 60 204

 When the conversion is complete, carry out a safety check to DIN EN 60 204.

 Follow the procedure described in section 2, page 146 onwards.

3.6 Converting the power supply from 3 x 208 VAC to 3 x 400 VAC

RISK OF DEATH 3

 Disconnect the machine correctly as described in section 1, page 145.

 Disconnect the machine from the main power supply.

 Take suitable action to ensure that the machine cannot be connected to the power supply dur-

ing the conversion work.

 Put up warning signs to indicate that work is being carried out on the electrical system.

Assembly Instructions, Converting the Power Supply 3 Converting the power supply on HF machines

12/2013 Edition 3.6 Converting the power supply from 3 x 208 VAC to 3 x 400 VAC

167

3.6.1 Removing the power supply unit

Fig. 3 - 13 Accessing the power supply unit

(1) Operator panel on the power supply side

(2) Main switch

(3) Door lock

(4) Cover

(5) Recess for power cable infeed

 Open the lock (item 3 in Fig. 3 - 13) on the protective door (item 4 in Fig. 3 - 13 using the ma-

chine key.

 Detach the holding cord from the cover.

 Use the Allen key to loosen the M8 locking screw (item M8 in Fig. 3 - 14) on the lower front

panel.

 Pull the power supply unit out as far as the stop.