X3_X4_Series machine - 第192页
4 Setting up and commissioning User manual SIPLACE X-Series 4.4 Setting up the placement machine Software Version SR.601.xx 11/2005 US E dition 192 4.4.4 Presett ing the PC B transport height Æ Push the forks of th e for…
User manual SIPLACE X-Series 4 Setting up and commissioning
Software Version SR.601.xx 11/2005 US Edition 4.4 Setting up the placement machine
191
4.4.3 Tools and equipment
You will need the following tools and equipment to adjust the height of your placement machine:
– Fork wrench, size 36, item no. 00096286-01
Size 36 for the adjusting screw M24x2x120 to adjust the height of the machine feet 4
– Hook wrench 135 - 145 for adjusting the middle machine feet
Item no. 00376519-xx 4
– Single-ended spanner, size 65, item no. 00353827-01
Size 65 for the hexagon lock nut M24 on the middle machine foot 4
– Allen key, size 10, item no. 00373926-01
for hexagon socket head screws M12x80 for fixing the spacers for the middle machine feet4
– Allen key, size 19, item no. 00373928-01
for hexagon socket head screw M24x90 for clamping the four outer machine feet clamps4
–Fork-lift
Fork length: min. 1800 mm 4
Carrying power: min. 6000 kg 4
Width between forks: see Fig. 4.4 - 1
4
– Spirit level : accuracy 0.02 mm/m
– Air cushion transport system: SIPLACE HSxx, item no. 00119002-xx
4 Setting up and commissioning User manual SIPLACE X-Series
4.4 Setting up the placement machine Software Version SR.601.xx 11/2005 US Edition
192
4.4.4 Presetting the PCB transport height
Æ Push the forks of the fork-lift under the placement machine, as shown in Fig. 4.4 - 1.
4
Fig. 4.4 - 1 Contact surfaces - Forks parallel to the direction of PCB transport
(1) Contact surfaces for the forks of the fork-lift
WARNING 4
Please note the following points
before
you raise the placement machine in order to avoid irre-
versible damage to the machine:
– Open the forks just wide enough to position them between the two machine feet (the attach-
ment points are shown in Fig. 4.2 - 3
). The machine feet are 776 mm apart. NEVER increase
User manual SIPLACE X-Series 4 Setting up and commissioning
Software Version SR.601.xx 11/2005 US Edition 4.4 Setting up the placement machine
193
the distance between the forks so that the machine is lifted on the side parts of the machine
frame, since this would deform the machine frame.
Æ Make sure that the forks are evenly loaded when you lift the machine. A firm support between
the forks and placement machine will prevent the machine tilting when it is raised. This will
also prevent a one-sided load on the machine feet, which would deform the fixing of the ma-
chine feet. We recommend that a second person watch the machine as it is raised, and make
sure that the machine does not tip to one side when lifted with the fork-lift.
Æ With the fork-lift, raise the machine approximately 35 cm. This will avoid any risk of injuring
your feet if you lower the machine feet accidentally.
The placement machine stands on 6 feet.
– 4 outer machine feet (item 1 in Fig. 4.4 - 3
)
There are two versions of the outer machine feet: 4
– outer machine foot for the PCB conveyor height of 830 mm, length 369 mm,
item no. 03041008-01 (item 1 in Fig. 4.4 - 3
, page 194)
– outer machine foot for the PCB conveyor heights of 900, 930 and 950 mm, length
439 mm, item no. 03000890-02 (item 2 in Fig. 4.4 - 3
, page 194)
– 2 middle machine feet (item 2 in Fig. 4.4 - 3
) with 2 spacers (items 3 and 4 in Fig. 4.4 - 3) for
adjusting the height, if necessary.
4
Fig. 4.4 - 2 Outer machine feet - two versions (dimensions in millimeters)