德森印刷机说明书之操作手册-4d1321fc284ac850ac024234 - 第19页
深圳德森精密设备有限公司 Shenzhen Desen Pre cision Machine Co., Ltd. - 19 - 第三章 生产工 作流程 Chapter Chapter Chapter Chapter III III III III P r oduction P r oduction P r oduction P r oduction Flow Flow Flow Flow 3.1 3.1 3.1 3.1 开机前 检查 3…
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 18 -
11)
在线 PCB 板计数 PCB Courting
12)
2D 检测和 CPK 分析 2D Inspecting and CPK analysis
2.6.2
2.6.2
2.6.2
2.6.2
软件安装
2.6.2
2.6.2
2.6.2
2.6.2
Software
Software
Software
Software
Installation
Installation
Installation
Installation
机器出厂前已经安装了驱动软件和操作系统软件。在使用过程中，如须重新安装，请按
下列步骤进行。 （详细信息请参考随机 CD 中 ” 安装说明 .txt ” ）
The software is installed b efore the machine shipment . If the software must be install ed
again , please follow the step s below: (see “ Installation instruction.txt ” on the CD delivered
together with the printing machine for detailed information).
1)
在驱动器中放入随机的 CD 盘。
Put the installation CD into the driver.
2)
打开 CD 盘，把 printer 文件复制到计算机 C 盘的根目录下。
Copy “ Printer ” directory into the root directory.
3)
然后打开 printer 文件，点击 文件来注册。
Enter into “ printer ” , click “ regni ” to install the files.
4)
完成后把文件 printer.exe 发送快捷方式放到桌面上。
Create short cut of “ printer.exe ” on desktop.
5)
在桌面上双击 printer.exe 即可打开 DSP-1008 主程序。
Double click printer.exe to enter the main program DSP-1008.
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 19 -
第三章 生产工作流程
Chapter
Chapter
Chapter
Chapter
III
III
III
III
Production
Production
Production
Production
Flow
Flow
Flow
Flow
3.1
3.1
3.1
3.1
开机前检查
3.1
3.1
3.1
3.1
Inspections
Inspections
Inspections
Inspections
before
before
before
before
startup
startup
startup
startup
检查所输入电源的电压、气源的气压是否符合要求；
Inspect whether the voltages and electric sources of all input power supplies comply with
the requirements;
检查机器各接线是否连接好；
Inspect whether the wiring of printing machine is qualified;
检查设备是否良好接地；
Inspect whether the printing machine is well grounded;
检查气动系统是否漏气，空气输入口过滤装置有无积水，是否正常工作。
Inspect whether the pneumatic system suffers from air leakage; and whether the filter
at
the air inlet has waterlogging water and whether
it
is operating normally;
检查机器各传送皮带松紧是否适宜；
Inspect whether the tight degree of each feed belt of the printing machine is proper;
检查是否有无关的碎物留在电控箱内，电控箱内各接线插座是否插接良好；
Inspect whether there are any broken items left in the electric control box and whether the
inserting conditions of the connector socket
s
in the electric control box are good;
检查有无工具等物遗留在机器内部；
Inspect whether there are nay tools and some other items left in the printing machine;
根据所要印刷的 PCB 板要求，准备好相应的网板和锡膏；
Prepare the needed screen and solder paste in compliance with the requirements of the
PCB boards to be printed;
检查磁性顶针和真空吸盘是否按所要生产的 PCB 尺寸大小摆放到工作台板上 ;
Inspect whether the magnetic thimble and vacuum chuck are positioned on the workbench
as per the size of PCB boards to be produced;
检查清洗用卷纸有无装好，检查酒精箱的液位（液面应超出液位感应器） ；
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 20 -
Inspect whether the cleaning paper has been well mounted and whether the liquid level of
alcohol tank is higher than the liquid level sensor;
检查机器的紧急制动开关是否弹起；
Inspect whether the emergency brake switch of printing machine is bounced; and
检查三色灯工作是否正常，检查机器前后罩盖是否盖好。
Inspect whether the three-color indicator light operates normally and whether the front and
back covers cover the printing machine well.
3.2
3.2
3.2
3.2
开始生产前准备
3.2
3.2
3.2
3.2
Preparations
Preparations
Preparations
Preparations
before
before
before
before
production
production
production
production
3.2.1
3.2.1
3.2.1
3.2.1
范本的准备
3.2.1
3.2.1
3.2.1
3.2.1
Preparation
Preparation
Preparation
Preparation
of
of
of
of
sample
sample
sample
sample
1)
模板基材厚度及窗口尺寸大小直接关系到焊膏印刷质量，从而影响到产品质量。范本
应具有耐磨、孔隙无毛刺无锯齿、孔壁平滑、焊膏渗透性好、网板拉伸小、回弹性好
等特点。
1) The formwork base material thickness and window size have a direct bearing on the printing
quality of solder paste and further the product quality. T he samples shall be friction resistant and
free from burr and saw teeth in pores and have other characteristics such as smooth pore walls,
good penetrability of solder paste, small stretching range of screen and sound rebound elasticity ;
and
2)
根据网框尺寸大小移动网框支承板，将网框前后、左右方向的中心对准印刷机前横梁
及左、右支承板上的标尺 “ 0 ” 刻度位置，居中摆放后，再将网板锁紧。
2) Move the screen frame bearing plates in accordance with the screen frame
’
s
size, make the
centers of screen frame in front, rear, left and right directions align with the front beam of printing
machine and the “ 0 ” scale positions on the left and right bearing plates. Place the bearing plates in
the center before locking the screen.