德森印刷机说明书之操作手册-4d1321fc284ac850ac024234 - 第50页
深圳德森精密设备有限公司 Shenzhen Desen Pre cision Machine Co., Ltd. - 50 - 图 4- 26 〈详细数据〉 Fig ure 4- 26 D etailed D ata 进入方式：主工具中 [ 程序编辑 ]+[ 详细数据 ] T o e nter the d ialog b o x, click E dit P rog ram a nd D etailed Data i n the m a…
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 49 -
To
enter the dialog box, click Edit Program.
说明：
Notes:
Notes:
Notes:
Notes:
只要将 PCB 参数设置好后，图中的 “ 印刷起点
”
、
“ 印刷长度
” “
清洗起点
” “
清洗 长
度
”
数值自动生成， 用户也可以根据生产的实际情况进行修改； 输入数值应大于 P CB
板的宽度。
As long as the PCB parameters are well set, the values of Printing Start Point, Printing
Length, Cleaning Starting Point and Cleaning Length will be created automatically. T hese
values can be amended in compliance with the actual conditions of production. T he input
values shall be larger than PCB board width;
在 [ 生产编辑 ] 中输入 PCB 板的长、宽、厚参数后，则运输宽度无需设定，自动显 示
为 “ PCB 板宽 +1
”
。
After the length, width and thickness parameters of PCB board are inputted in Production
Edit, the transport width is unnecessary to set and will be displayed as “ PCB board
’
s
width
+ 1 ” automatically;
在进行参数设置时，如所输入的数值超出机器设置范围，屏幕会显示 “ 输入超出 范
围 ” 的错误提示，并告诉你所输入参数的机器设置范围。
When in the parameter setting, if the inputted value goes beyond the setting scope of
printing machine, the screen will display an error prompt of “ Input exceeds scope ” and
give the correct setting scope of the inputted parameter; and
设置刮刀压力、刮刀速度、选择单刮或双刮及刮刀的运行方向；可选择 “
干、湿、
吸真空
”
自动清洗方式及清洗的速度和时间间隔， 也可选择行动的 “ 人工清洗方 式
” ；
可设置标志点图标类型；如图 4 – 26 所示：
Set the squeegee pressure, scrapper speed, single/double squeegees, and the moving
direction of squeegee. C hoose the “ dry/wet/vacuumized ” automatic cleaning manner and
the rate and time interval of cleaning or choose “ Manual cleaning manner ”
.
I
t
can set
signalized point icon type. S ee Figure 4-26.
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 50 -
图 4- 26 〈详细数据〉
Figure 4-26 Detailed Data
进入方式：主工具中 [ 程序编辑 ]+[ 详细数据 ]
To
enter the dialog box, click Edit Program and Detailed Data in the main tool bar respectively.
可设置视觉校正的取象方式 —— 双照或只第一次双照；还可对印刷精度进行设置。
It
can set the image taking manner, double-image-taking or the double-image-taking of the
first time, of visual calibration. I
t
can also set the printing precision.
注意：
Cautions:
Cautions:
Cautions:
Cautions:
a)
在设置视觉校正的取象方式时，如选择只第一次双照，则开始生产时只首次双照，
以后每次进板只对 PCB 板进行单照。
a) If the double-image-taking of the first time is chosen when setting the image taking manner
of visual calibration, only double-image-taking of the first time is taken in earlier stage of
production. A nd only single-image-taking is practiced for PCB boards in the board incoming of
each time;
b)
如在此对话框中选择手动的 “ 人工清洗方式
”
，在正常生产过程中，机器会按此
对话框中所输入的 “ 清洗间隔 ” 参数生产完一定数量的产品后自动停下，并出现 “ 人 工
清洗 ” 对话框，如图 4 – 27 所示，等待人工清洗网板，步骤如下：
b) If “ Manual cleaning manner ” is chosen in the dialog box, in normal production, the
printing machine will stop automatically after producing some products based on the
“ Cleaning interval ” parameter inputted in the dialog box, meanwhile, “ Manual cleaning ”
dialog box as shown in Figure 4-27 will emerge, waiting for the manual cleaning of screen.
T he steps are as follows:
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 51 -
图 4- 27 〈人工清洗〉对话框
Figure “ Manual Cleaning ” Dialog Box
在
“ 人工清洗
”
对话框中单击 “ 打开门开关
”
按钮， 将机器前罩门打开， 并单击 “ CCD
回位 ” 按钮，使 CCD 部分回到原点位置。
Click “ Open Door Switch ” in the “ Manual Cleaning ” dialog box to open the printing
machine
’
s
front door, then click “ CCD Return ” to make CCD return to the origin partially.
此时可将手伸到网板下进行人工清洗网板。
At this time, hand can stretch under the screen for manual cleaning.
清洗完成后将前罩门关闭，并按下机器操作面板上的继续操作 “ START ” 按钮，黄
色指示灯会亮，机器继续开始生产。
Close the front door after the cleaning and press the “ START ” button on the operation panel
of printing panel for continuous operation. T hen the yellow indicator light will be on and
the printing machine starts production continuously.
2.
2.
2.
2.
[PCB
[PCB
[PCB
[PCB
定位 ]
]
]
]
2.
2.
2.
2.
PCB
PCB
PCB
PCB
Locating
Locating
Locating
Locating
PCB 定位調試的操作程式
It
is the operation program for location and debugging of PCB boards.
1)
首行要确认停板气缸的位置居中且合适；
1) Firstly, confirm whether the position of board stop cylinder is in the middle and appropriate;
移动挡板气缸 打开停板气缸 打开运输开关 PCB 从入口处
进板 关闭运输开关 打开 PCB 吸板阀 关闭停板气缸（收回）
平台顶板 导轨夹紧 CCD 回位
Move the board stop cylinder, open the board stop cylinder, switch on the transport switch ,
feed PCB boards from the entrance, switch off the transport switch, switch on the PCB board
absorbing valve, close the board stop cylinder (withdraw), platform top slab, clamp guide rail,
and make CCD return.
注意：点击 “ 平台顶板 ” 按钮，使 PCB 支撑块处入顶板位置，手动将 PCB 放于支撑块上
，