MEC-CP842-1.0E.pdf - 第112页
Replacing Consumable Parts >> Waste Tape Cu tter 6-4 MEC-CP842-1.0E 6.3 W aste T ape Cutter Point A broken or damaged waste ta pe cutt er will not cut the waste ta pe properly , causing tape clogging and tape feed …
Replacing Consumable Parts >> Fluorescent Nozzle Stickers
MEC-CP842-1.0E 6-3
7 Use a cutter to trim off any of the sticker that protrudes beyond the disk.
8 Remove any of the adhesive that may have adhered to the nozzle pipe.
Nozzle and fluorescent sticker drawing numbers
C746M4T01
ADCPH751*
ADCPH769*
ADCPH752*
ADCPH753*
ADCPH754*
ADCPH955*
ADCPH956*
ADCPH957*
ADCPH958*
ADCPH770*
ADCPH971*
ADCPH959*
ADCPH961*
ADCPH963*
ADCPH965*
ADCPH960*
ADCPH962*
ADCPH964*
ADCPH966*
ADCPH968*
DCPH851*
DCPH851*
DCPH852*
DCPH853*
DCPH854*
DCPH855*
WPH820*
WPH821*
DCPH856*
DCPH854*
WPH820*
DCPH857*
DCPH858*
DCPH859*
DCPH860*
DCPH881*
DCPH882*
DCPH883*
DCPH884*
DCPH885*
Nozzle Size
Nozzle
shape
Round
Round
Round
MELF
Nozzle Assy
Dwg. No.
Disk Size
Fluorescent Seal
Dwg. No.
f 0.4 ( R08-004 )
f 0.4 ( R08-004 ) Short
f 0.7 ( R08-007 )
f 1.0 ( R08-010 )
f 1.3 ( R08-013 )
f 1.8 ( R16-018 )
f 2.5 ( R16-025 )
f 3.7 ( R16-037 )
f 5.0 ( R16-050 )
f 1.3 ( M08-013 )
f 2.5 ( M16-025 )
f 1.8 ( S16-018 )
f 2.5 ( S16-025 )
f 3.7 ( S16-037 )
f 5.0 ( S16-050 )
f 1.8 ( B16-018 )
f 2.5 ( B16-025 )
f 3.7 ( B16-037 )
f 8
f 8
f 8
f 8
f 8
f 16
f 16
f 16
f 16
f 8
f 16
16x16
16x16
16x16
16x16
16x16
16x16
16x16
16x16
21x21
f 5.0 ( B16-050 )
f 5.0 ( B21-050 )
Replacing Consumable Parts >> Waste Tape Cutter
6-4 MEC-CP842-1.0E
6.3 Waste Tape Cutter
Point
A broken or damaged waste tape cutter will not cut the waste tape properly, causing
tape clogging and tape feed problems. The waste tape cutter must be replaced at such
times.
Procedure
1 Remove the plate located above the waste tape cutter.
2 Remove the two bolts which secure the fixed cutter.
3 Remove the two bolts which secure the arm of the moving cutter.
4 Remove the fixed and moving cutters, and mount the new fixed and moving cut-
ters.
Note: Apply grease to the contact points before attaching the moving cutter.
(See 5.2.9 Lubricating the Waste Tape Disposal Unit)
WARNING
• Turn the main power off before performing this procedure.
• Spring recoil may cause the cam to rotate suddenly if not at its
origin position (0°). Working inside the machine is dangerous
and requires special care.
C746M4004
Moving cutter
Fixed cutter
Arm
Plate
Replacing Consumable Parts >> Conveyor Belts
MEC-CP842-1.0E 6-5
6.4 Conveyor Belts
Point
Broken or damaged conveyor belts must be replaced.
Procedure
1 Remove the panel lifter. The mounting bolts are at the bottom.
2 Loosen the bolt that secures the tension pulley.
3 Loosen the belt guide bolts.
4 Replace the conveyor belt.
5 Insert a 0.3 mm clearance gauge between the belt’s top surface and the plate,
then tighten the belt guide bolts while maintaining this 0.3 mm clearance.
6 Tighten the belt by applying 1 to 1.5 kg of force to the tension pulley in the
direction indicated by the arrow, then tighten the tension pulley bolt.
Note: The belt can also be tightened to the prescribed tension by tightening the tension pulley bolt
while pushing the tension pulley 1 to 2 mm in the direction indicated by the arrow.
WARNING
Turn the main power off before performing this procedure.
C746M4005
Belt guide bolt
Panel lifter
Tension pulley
Plate
Horizontal
adjustment bolts
Mounting bolts