MEC-CP842-1.0E.pdf - 第2页
Copyright s All rights re garding this manual are reserved by Fuji Machine Manufacturing Co., Ltd . This manual may not, in whole or in part, be reproduc ed by any mean s (ele ctronic, mechanical or otherwise), or reused…
The manuals listed below are shipped with this machne.
CP-842E/CP842ME Oprator’s Guide
CP-842E/CP842ME System Reference
CP-842E/CP842ME Mechanical Reference
In order to operate this machine in the safest and most efficient
manner, please read the provided manuals thoroughly and
observe all instructions and warnings.
Keep these manuals in an accessible location near the machine.
High-Speed Chip Placer
CP-842E
CP-842ME
Mechanical Reference
MEC-CP842-1.0E
R
Copyrights
All rights regarding this manual are reserved by Fuji Machine Manufacturing Co., Ltd. This manual may
not, in whole or in part, be reproduced by any means (electronic, mechanical or otherwise), or reused in
any way, without the prior written permission of Fuji Machine Manufacturing Co., Ltd.
Trademark Rights
is a trademark of Fuji Machine Manufacturing Co., Ltd., and registered in the following
countries: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Indonesia, Ireland, Italy, Japan,
Korea, Luxembourg, the Netherlands, Portugal, Spain, Sweden, the U.K., and the U.S.A.
WindowsNT is a trademark of Microsoft Corporation, USA.
UNLHA(32).DLL is a freeware product created by Micco.
Warranty and Liability
Fuji Machine Manufacturing Co., Ltd. accepts no responsibility for situations that may arise due to any of
the following:
• The use of third party parts.
• The use of non-genuine Fuji parts.
• Incorrect settings made by the customer.
• Improper use of Fuji equipment.
Notice
Fuji Machine Manufacturing Co., Ltd. reserves the right to change the content of this manual without
notice.
Every effort has been made to ensure that this manual is correct in every detail. However, please contact
Fuji in the unlikely event that errors or omissions are detected.
Fuji Machine Manufacturing Co., Ltd. accepts no responsibility for any situations that may arise as a result
of the use of this manual.
R
Table of Contents
MEC-CP842-1.0E 1
1. About This Manual ..........................................................................1-1
1.1 Manual Structure ...................................................................... 1-1
1.2 Page Layout .............................................................................1-2
1.3 Notation Conventions Used in this Manual...............................1-3
2. Safety ...............................................................................................2-1
2.1 About Symbols .........................................................................2-1
2.2 Safety Rules for All Machine Types..........................................2-2
2.3 Safety Rules for Individual Machine Types...............................2-7
2.3.1 CP-842E/842ME Machines ....................................................2-7
2.4 Safety Labels............................................................................2-8
2.5 The EMERGENCY STOP Buttons .........................................2-11
3. The Machine ....................................................................................3-1
3.1 Machine Components...............................................................3-1
3.1.1 General View ......................................................................3-1
3.1.2 Servo Control Axes.............................................................3-5
3.1.3 Rotary Head........................................................................3-5
3.1.4 Placing Head ......................................................................3-6
3.1.5 PCU (Pallet Change Unit)...................................................3-6
3.2 Functions of Each Part .............................................................3-7
3.2.1 Parts Mounting System.......................................................3-7
3.2.2 Parts Supply System .........................................................3-8
3.2.3 Vision System .....................................................................3-9
3.2.4 Panel Conveyance System.................................................3-9
3.2.5 Electrical Control System....................................................3-9
3.3 Sensor Positions.....................................................................3-11
3.3.1 XY-table ............................................................................3-11
3.3.2 In-conveyor .......................................................................3-13
3.3.3 Out-conveyor ....................................................................3-14
3.3.4 Main Conveyor..................................................................3-15
3.3.5 In-carrier ...........................................................................3-16
3.3.6 Out-carrier.........................................................................3-17
3.3.7 Panel Clamp .....................................................................3-18
3.3.8 Cam Box ...........................................................................3-19
3.3.9 Tape Feeder Unit (ST1, 2)................................................3-20
3.3.10 Tape Cutter (ST1).............................................................3-21
3.3.11 Nozzle Clutch (ST10)........................................................3-22
3.3.12 Nozzle Changer (ST15) ....................................................3-23
3.3.13 Feeder Check ...................................................................3-24
3.3.14 Device Table.....................................................................3-26
4. Basic Operation...............................................................................4-1
4.1 Changing the Conveyor Width..................................................4-1
4.2 Changing the Panel Back-up Pin Positions ..............................4-3
4.3 Setting the Feeders .................................................................. 4-5
4.4 Removal and Installation of Rotary Holders .............................4-7