2500_Users_Manual - 第411页
Computer Remote Control ProM aster 25 00 User Manua l E-23 27 End of user RAM exceeded 28 Fata l device-specific programm ing error 29 Non-fatal device-specific programming error 2A Device Insertion error Note : T he two…
Computer Remote Control
E-22 ProMaster 2500 User Manual
CRC Error Codes
Following is a list of error codes that appear while the 2500 programming
electronics are being operated in the computer remote control mode.
These error codes will be returned by the 2500 programming electronics
after they receive the
X
command. Normally, you should send the
X
command after the 2500 programming electronics send an
F
in response to
a command. The list is in numerical order, according to the error code.
1F Cannot erase device error
20 Non-blank device
21 Illegal bit error
22 Device programming error
Note: The two following errors have the same error code. For either error to
appear, you must have selected command
n23]
(Select Verify Option). If
1
was specified as the variable, use the first description. If
2
was specified,
use the second description.
23 Verify data error (Vcc Nominal)
23 Verify data error (Vcc low)
24 Verify data error (Vcc high)
59] Enable/disable capacitor
configuration test >
5A] Display list of parameters See Application Note*
5B] Clear vector data >
5C] Load system files for CM algorithm
disk >
5D] Write system files to CM disk >
5E] Write algorithms to CM disk >
n
5F] Select algorithm source drive for
creating CM algorithms >
60] Get number of sectors dd>
n
61] Get sector configuration settings HHHH HHHH>
nhhh...hhhh
62] Set sector configuration settings >
xxx...xxxx
64] Select device part number for CM (use
xxx...xxxx
33] to select manufacturer) >
A7] Swap bytes >
DC] Device check See Application Note*
EB] Input JEDEC data from host >
EC] Output JEDEC data to host >
FC] Restore CRC entry default parameters >
FD] Restore user-defined CRC parameters >
FE] Save user-defined CRC parameters >
* This Application Note, “UniSystem Computer Remote Control,” is available from Data I/O
Customer Support.
Command Description Response
Computer Remote Control
ProMaster 2500 User Manual E-23
27 End of user RAM exceeded
28 Fatal device-specific programming error
29 Non-fatal device-specific programming error
2A Device Insertion error
Note: The two following errors have the same error code. For either error to
appear, you must have previously selected command
n23]
- where n = 0, 1,
or 2. If a 0 is chosen, there will be no error condition. (Select Verify
Option). If
1
was specified as the variable, use the first description. If
2
was specified, use the second description.
2B Structured test error (Vcc Nominal)
2B Structured test error (Vcc low)
2C Structured test error (Vcc high)
2D Base/Adapter for device not installed
2E Programming hardware hasn’t passed self-test
30 Device algorithm not found
31 Device over-current fault
3B No device present
40 I/O initialization error
41 Serial-framing error
42 Serial-overrun error
43 Serial framing/overrun error
46 I/O timeout
52 Data verify error
75 Security Fuse Violation
77 Security fuse programming error
79 Preload not supported by this device
81 Serial-parity error
82 Sumcheck error
84 I/O format error
88 Invalid number of parameters
89 Illegal parameter or invalid operation selected
8B Error restoring/saving CRC user-defined parameters or restoring
CRC entry defaults.
8E File error
8F NON-JEDEC data present in RAM or disk file, or else a non-logic
device was selected with a JEDEC I/O translation format selected
90 Illegal I/O format
94 Data record error
97 Block move error
98 End of device exceeded
99 End of file exceeded
9A Algorithm disk cannot be found
Computer Remote Control
E-24 ProMaster 2500 User Manual
9B Incompatible system/algorithm disks or incompatible device
libraries
9C Invalid command for this mode
9D I/O address beyond range of data format selected
A1 No Electronic ID
A2 Electronic ID verify error
AB Unable to load system file from system disk
AC Security violation
AE Keep Current algorithm disk not found. Insert your Keep Current
algorithm disk
AF Operation not allowed because the device was selected by family/
pinout code
B0 Capacitor configuration error
B1 Block not allowed for bulk erase
B2 Partial device operation not allowed
B4 Odd Memory Begin Address or User Data Size Incompatible with
Data Word Width
B6 Algorithm doesn’t have a footnote
B8 Algorithm or Logic disk not found
B9 Algorithm disk 2 or Memory disk not found
BA Yield Tally access/update error
BC Last device operation checksum not available
D5 Port Transfer Error
E30Ribbon not detected
E31Ribbon latch not engaged
FE Undefined error
FF Operation aborted at programmer