SM-131-006.pdf - 第63页

Device Name Chip Mounter Block Name Page No. Unit Name Revision Model Item GXH-1 (3) Set up the glass jig PCB. After setting up the conveyor width, place the glass jig PCB on the positioning center by hand. Be sure to al…

100%1 / 325
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
2.3 Automatic Offset
2.3.1 PEC Recognition Camera and Beam Offsets
• Confirmatory Operation of Offset Values
(1) Select one of the [1], [2], [3], and [4] buttons in the "camera/beam select" group box of
the "RECOG CAMERA & BEAM OFFSET" window. (Operation Sequence: [MAINT.]
Button → [TEACHING] Button → [OTHERS] Button → [PEC RECOG & BM OFST]
Button)
Select the [Not use] button in the "Glass jig" group box.
Select the [Teach Start] button and press the [START] button to start the teaching
operation.
When there is not a big difference in the values between "Crnt" and "Adj", it is
not required to perform this teaching operation.
Otherwise, the teaching operation must be performed, using the glass jig PCB.
(2) Follow the same procedure for "[1] through [4]" in the "camera/beam select" group box.
Required Jig : Glass Jig PCB (460 × 250 mm)
No support pin is required.
• Clamping Procedure of Glass Jig PCB
(1) Zero the conveyor width.
Open the "PROD. CHG." window by pressing the [PROD. CHG.] button
and zero the L conveyor, the conveyor, and the R conveyor.
(2) Change the conveyor width.
Open the "ADJUST" window and select the [Stage #1] or the [Stage #2]
button. (Operation Sequence: [OPERATOR] Button → [MAINT.] Button
→ [DVC CHECK] Button → [ADJUST] Button)
Set "BackUp Base" in the "Opn mode" text box in the P.C.B. transfer"
group box.
Enter "250.5" for "Wd" and "114.75" for "Ofst" in relation with each item
"stg#1", "Center", "Stg#2" in the "Suiting of width of conveyor (Start)"
group box.
When each button in the "Suiting of width of conveyor (Start)" group box
is selected and the [START] button is pressed, the corresponding
conveyor width is changed.
Enter "250" in the "Tgt Wd" text box and "0.8" in the
"Clearance" text box, "115" in the "Base Pos" text box in the
"Cnvr Wd" group box of the "PRODUCT CHANGE" window.
Move the L conveyor, the conveyor, and the R Conveyor to the
target positions.
Example : Selecting [L Cnvr] Button → Selecting [Desig
Width] Button → Pressing [START] Button
Heads
2. Installation Offset
1-9
0403-001
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
(3) Set up the glass jig PCB.
After setting up the conveyor width, place the glass jig PCB on the
positioning center by hand.
Be sure to align the glass jig PCB with the outer edges of the center
conveyor. (See Fig. A8.)
(4) Make the glass jig PCB clamped.
Open the "ADJUSTMENT" window and select the [Stage #1] or the
[Stage #2] button. (Operation Sequence: [OPERATOR] Button →
[MAINT.] Button → [DVC CHECK] Button → [ADJUST] Button).
Select the [Inp/Pos PCB] button in the "P.C.B. transfer" group box.
Press the [START] button. The clamping is completed.
• When the [START] button is pressed after the [Out PCB] button, the
clamping is released.
• Procedure for Teaching Operation
(1) Select one of the [1], [2], [3], and [4] buttons in the "camera/beam select" group box of
the "RECOG CAMERA & BEAM OFFSET" window. (Operation Sequence: [MAINT.]
Button → [TEACHING] Button → [OTHERS] Button → [PEC RECOG & BM OFST]
Button)
Select the [Use] button in the "Glass jig" group box.
Select the [Teach Start] button and press the [START] button to start the teaching
operation.
(2) Follow the same procedure for "[1] through [4]" in the "camera/beam select" group box.
(3) Select the [End] button.
The "Confirmation to Saving" dialog box opens. Select the [Yes] button.
The teaching session is terminated.
⇒Conveyor
Machine Reference Side
Conveyor
Jig PCB
Fig. A8 Position of Glass Jig PCB
Stage 1
Stage 2
Outer Edges of Center Conveyor
Heads
2. Installation Offset
1-10
0403-001
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
2.3.2 Component Recognition Camera Offset (Execution of Offset Teaching
Operation)
Required Jigs : Component Recognition Offset Jig JG-0085 (Standard Accessory Part)
Nozzle for Jig Pickup φ6 mm (Nozzle Type HA09)
• Procedure for Teaching Operation
(1) Put the jig on the jig depository.
(Left Front Side of Component Recognition Camera: Sides 1 and 4, Right Front Side:
Sides 2 and 3)
(2) Attach the vacuum nozzle to the Nozzle No. 1 position.
(3) Select one of the [1], [2], [3], and [4] buttons in the "Select camera" group box of the
"COMPONENT RECOG CAMERA OFFSET" window and confirm that "1" is set in the
"Nozzle No." text box in the "Designate Nozzle" group box. (Operation Sequence:
[MAINT.] Button → [TEACHING] Button → [OTHERS] Button → [CMP RECOG
CAMR OFST] Button)
(4) Select the [Teach Start (Offset Data)] button and press the [START] button.
(5) Follow the same procedure for "[1] through [4]" in the "Select camera" group box.
(6) Select the [End] button.
The "Confirmation to Saving" dialog box opens. Select the [Yes] button.
The teaching session is terminated.
As "0.04°" is set for "Pick-up difference tol Angle [deg]", the teaching operation
is automatically repeated the number of the specified times until the difference
becomes less than "0.04°".
Heads
2. Installation Offset
1-11
0403-001