SM-131-006.pdf - 第78页

Device Name Chip Mounter Block Name Page No. Unit Name Revision Model Item GXH-1 Chapter 3 Various Setting 2. Setting of Various Boards 2.3 Setting of UB21 Boards (Relay Boards 2) • Two pieces of UB21 boards are used in …

100%1 / 325
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
Chapter 3 Various Setting
2. Setting of Various Boards
2.1 Table of Boards with Various Adjusting Switches
Table of Boards with Various Adjusting Switches Table C2
Board Types
No.
Board
Symbols
Board Names
U NO Location
Reference
Item Nos.
1 UB20 Relay Board 1 U26 BH Section (Center below
Frame on Rear Side)
2.2
2 UB21 Relay Board 2 U27 Power Supply Section (One
Board each for BL and BR)
2.3
3 UA54 ILB Board U05 Power Supply Section (One
Board each for BL and BR)
2.4
4 UB14 I/O Board U12 Power Supply Section (One
Board each for BL and BR)
2.5
5 UB14 I/O Board U08 Transfer Section 2.5
6 UB14 I/O Board U09 Cutter/Positioning Section 2.5
7 UB13 I/O Board U01 Operation Panel Front/Rear 2.6
8 UB13 I/O Board U11 Light Tower 2.6
9 UA53 I/F Board U07 Signals between Main Machine
and Input/Output Machines
2.7
10 UB22 I/O Board U04 Head (Doughnut Board) 2.8
11 Multiaxis Driver Board Power Supply and Head
Sections
2.9
12 Motion Control Board U82 Inside CPU2 Box 2.10
13 Motion Control Board U83 Inside CPU2 Box 2.10
14 Motion Control Board U84 Inside CPU2 Box 2.10
15 HLS Center Board U85 Inside CPU2 Box 2.11
16 Linear Measure Sensor Control Board U03 Head Wiring Section 2.12
2.2 Setting of UB20 Board (Relay Board 1)
• A piece of UB20 board is used in the main body.
Refer to "1.3 Layout of BH Block" in
Chapter 13 for the location.
2.2.1 Setting of Jumper Wires
Set all Jumper Wires J23, J24, J27,
and J31 to "Short" as shown in
Fig. C2.
2.2.2 Setting of Timer
Set the time of K2 (Power ON Delay
Timer) in Fig. C2 to "1 sec".
Fig. C2 UB20
0406-001
3-2
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
Chapter 3 Various Setting
2. Setting of Various Boards
2.3 Setting of UB21 Boards (Relay Boards 2)
• Two pieces of UB21 boards are used in the power supply section.
Refer to "1.5 Layout of BL Block" and "1.6 Layout of BR Block" in Chapter 13 for
the location.
2.3.1 Setting of Jumper Wires
Set Jumper Wires J1, J36, J37, J62, and
J71 as shown in Fig. C3.
2.4 Setting of UA54 Boards (ILB Boards)
• Two pieces of UA54 boards are used in the power supply section.
Refer to "1.5 Layout of BL Block" and "1.6 Layout of BR Block" in Chapter 13 for
the location.
2.4.1 Setting of Dip Switches
Set Dip Switches SW1, SW2, SW3,
SW4, and SW5 as shown in Fig. C4.
2.4.2 ROM Mounting
Mount ROM as shown in Fig. C4.
Fig. C3 UB21
Fig. C4 UA54
0406-001
3-3
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
Chapter 3 Various Setting
2. Setting of Various Boards
2.5 Setting of UB14 Boards (I/O Boards)
• The UB14 boards are used at three places - Power Supply Section, Transfer
Section, and Cutter/Positioning Section.
Refer to "9. Layout of Various Boards" in chapter 13 for where they are arranged.
2.5.1 Setting of Dip Switches
• When the UB14 board is used in
the power supply section, set
SW1 like "A" in Fig. C5.
• When the UB14 board is
used in the transfer section,
set SW1 like "B" in Fig. C5.
• When the UB14 board is
used in the cutter/positioning
section, set SW1 like "C" in
Fig. C5.
2.5.2 Setting of Jumper
With Jumper JP1, short between two pins as shown in Fig. C5.
2.6 Setting of UB13 Boards (I/O Boards)
• The UB13 boards are used at three places - Front Operation Panel, Rear
Operation Panel, and Light Tower.
Refer to "9. Layout of Various Boards" in chapter 13 for where they are arranged.
2.6.1 Setting of Dip Switches
• When the UB13 board is used in
the front operation panel, set
SW1 like "A" in Fig. C6.
• When the UB13 board is used in
the rear operation panel, set SW1
like "C" in Fig. C6.
• When the UB13 board is used in
the light tower, set SW1 like "B"
in Fig. C6.
Fig. C5 UB14
Fig. C6 UB13
0406-001
3-4