slau358q.pdf - 第51页

www.ti.com Status Messages 51 SLAU358Q – September 2011 – Revised October 2019 Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated Operation ==== Errors from the BOOT loader. ==== ERROR # …

Status Messages

www.ti.com

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

Executing Main Process...

.............

2 : init target

3 : erasing-Info

4 : erasing-Info

5 : erasing-Info

6 : erasing-Main

7 : erasing-Main

8 : erasing-Main

9 : erasing-Main

10 : erasing-Main

11 : erasing-Main

12 : erasing-Main

13 : erasing-Main

14 : erasing-Main

15 : Blank-1800

16 : Blank-1880

17 : Blank-1900

18 : Blank-5C00

19 : Blank-10000

20 : Blank-20000

21 : Blank-30000

22 : Blank-40000

23 : Write-FC00

24 : Write-FC90

25 : Write-FD10

26 : Write-FD80

27 : Write-FFE2

28 : Verify-FC00

29 : Verify-FC90

30 : Verify-FD10

31 : Verify-FD80

32 : Verify-FFE2

33 : Gl.Verify-1800

34 : Gl.Verify-5C00

35 : Gl.Verify-10000

36 : Gl.Verify-20000

37 : Gl.Verify-30000

38 : Gl.Verify-40000

39 : closing target

40 : Done

0 : Finished

This report indicates that sectors INFO-B, INFO-C, INFO-D, and the main memory block have been

erased (tasks 2 to 14) blank checked (tasks 15 to 22), programmed (tasks 23 to 27) and verified (tasks 28

to 38). Finally, access to target devices is closed and the programming process is finished. Length of task

description (including consecutive task number) is limited to 16 characters to be able display this

information on the third line of the MSP Gang Programmer LCD display.

The MSP Gang Programmer can process up to 1000 tasks per one image saved in internal memory.

Having that number of available tasks and one or more code files saved in internal memory (total memory

footprint of up to 512KB in one image), the MSP Gang Programmer gives the user significant flexibility to

perform custom programming procedures. If for any reason the code files and task scripts require more

than 512KB of memory, then the next image memory can be taken and combined with the first one for one

larger image block (1Mbyte or more). The MSP Gang Programmer has internal flash memory of 8Mbyte

that can, if desired, all be used to form one image with a memory footprint of 8Mbyte.

Error messages are displayed similarly to status messages, however, programming is terminated if the

error is related to all target devices. Subsequently, if the problem is resolved or the faulty target device is

disabled, then the programming procedure can be restarted to complete the programming process. The

result for all devices is reported in the results section (green or red icons). When the global status is

reported as FAIL, see the result section for details. Similarly, the MSP Gang Programmer uses red and

green LEDs to indicate the result of its operations (red indicates failure) and details are displayed on the

LCD display. Below is the list of errors reported in the MSP Gang Programmer.

www.ti.com

Status Messages

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

==== Errors from the BOOT loader. ====

ERROR # 001 - BOOT Firmware only is in the MSP-GANG! The API Firmware should be downloaded.

ERROR # 002 - API Firmware CRC is not present! The API Firmware should be reloaded.

ERROR # 003 - API Firmware CRC error! The API Firmware should be reloaded.

ERROR # 004 - BOOT CRC error in the MSP-GANG!

==== Errors from the MSP-GANG Firmware. ====

ERROR # 010 - CRC Access key. Key corrupted. Access to programmer is blocked.

ERROR # 011 - Invalid programmer's access key. Access to programmer is blocked.

ERROR # 012 - Unknown interface.

ERROR # 013 - Vcc is too low.

ERROR # 014 - Vcc is too high.

ERROR # 015 - VtIO is too low.

ERROR # 016 - VtIO is too high.

ERROR # 017 - Header CRC. Image header is corrupted.

ERROR # 018 - Script CRC. Image script is corrupted.

ERROR # 019 - Exceed script number.

ERROR # 020 - Script command unknown.

ERROR # 021 - MCU Fetch synch failed.

ERROR # 022 - CPU JTAG synch failed.

ERROR # 023 - MCU device initialization failed.

ERROR # 024 - RAM firmware download failed.

ERROR # 025 - Flash blank check failed.

ERROR # 026 - Flash read verify failed.

ERROR # 027 - Flash write failed.

ERROR # 028 - Image flash write initialization failed.

ERROR # 029 - Image flash lock failed.

ERROR # 030 - Invalid script type/name.

ERROR # 031 - Script size too big.

ERROR # 032 - Used wrong MCU.

ERROR # 033 - IR communication failed.

ERROR # 034 - Page info number out of range.

ERROR # 035 - Address too high.

ERROR # 036 - Target number out of range.

ERROR # 037 - Address not even.

ERROR # 038 - Size not even.

ERROR # 039 - DCO calibration frequency out of range.

ERROR # 040 - DCO calibration failed.

ERROR # 041 - Gang flash write failed.

ERROR # 042 - SD Card - Read Response Error

ERROR # 043 - SD Card - Boundary Address Error

ERROR # 044 - SD Card - Initialization timeout

ERROR # 045 - SD Card - Read timeout

ERROR # 046 - SD Card - Initialization Error

ERROR # 047 - SD Card - CRC7 Error

ERROR # 048 - SD Card - CRC16 Error

ERROR # 049 - SD Card - Write CRC Error

ERROR # 050 - SD Card - Data Write Error

ERROR # 051 - SD Card - Write Timeout

ERROR # 052 - SD Card - MBR Sector Error

ERROR # 053 - SD Card - Volume Error

ERROR # 054 - SD Card - Address in File Error

ERROR # 055 - SD Card - Read File Error

ERROR # 056 - SD Card - File not found

ERROR # 057 - Hardware Rev-0. option not supported.

ERROR # 058 - Flash PSA verification failed.

ERROR # 059 - Flash read (Rx) data error.

ERROR # 060 - Vpp too low to secure fuse.

ERROR # 061 - Secure key incorrect.

ERROR # 062 - Secure device failed.

ERROR # 063 - Target not open, no access.

ERROR # 064 - BSL password wrong index.

ERROR # 065 - BSL read (Rx) timeout.

ERROR # 066 - BSL firmware download failed.

Status Messages

www.ti.com

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

ERROR # 067 - Unknown command.

ERROR # 068 - Fast BSL initialization failed.

ERROR # 069 - MSP-

GANG current overload. Reduce amount of target devices to 5 or select 30 mA output current.

ERROR # 070 - Wrong BSL passwords. Target cannot be unlocked.

==== Errors from the MSP-GANG DLL. ====

ERROR # 301 - Communication - Frame has errors !

ERROR # 302 - Unable to open COM port - already in use?

ERROR # 303 - Unable to close COM port !

ERROR # 304 - Unable to modify COM port state !

ERROR # 305 - Synchronization failed. Programmer connected?

ERROR # 306 - Timeout during operation - Correct COM port selected?

ERROR # 307 - Wrong baud rate specified !

ERROR # 308 - Communication Port baud rate change

ERROR # 309 - Communication port - diagnostic response error

ERROR # 310 - Open Comm port - invalid handle value

ERROR # 311 - Invalid Comm Port Setup

ERROR # 312 - Open Comm Port timeout

ERROR # 313 - Get Comm Port state error

ERROR # 321 - Command did not complete correctly !

ERROR # 322 - Command failed or not defined or Target not accessible !

ERROR # 323 - Could not read 'default.mspgangcfg'!

ERROR # 324 - File contains invalid record !

ERROR # 325 - Unexpected end of file !

ERROR # 326 - Error during file I/O !

ERROR # 327 - Selected file is of unrecognizable format !

ERROR # 328 - Unable to open file !

ERROR # 329 - Function argument(s) out of range !

ERROR # 330 - Note: Boot downloaded

ERROR # 331 - WARNING: Temporary function blocked, due to used main polling

ERROR # 332 - Image Memory corrupted or erased ! Load Image.

ERROR # 333 - Target not accessible !

ERROR # 334 - Verification failed !

ERROR # 335 - Main Process Parameters not yet set ! Load Image.

ERROR # 336 - Could not erase Image Buffer !

ERROR # 337 - Could not load Image Buffer !

ERROR # 338 - Could not load Main Process Parameters !

ERROR # 339 - Could not select Baud Rate !

ERROR # 340 - WARNING: Could not set target voltage -

Short circuitry or settling time too small?

ERROR # 341 - Invalid firmware command !

ERROR # 342 - Power supply voltage too low !

ERROR # 343 - WARNING: Sense voltage out of range - Check pin MSP_VCC_IN of target connector !

ERROR # 344 - Wrong target device connected !

ERROR # 345 - No target device connected

ERROR # 346 - File(s) contains already specified data (code overwritten)

ERROR # 347 - Selected Image number out of range

ERROR # 348 - Could not open the configuration file.

ERROR # 349 - Script Header size error

ERROR # 350 - Image ID error. Image ignored, program terminated.

ERROR # 351 - Image contents (size, no of tasks) error. Program terminated.

ERROR # 352 - Image CRC error. Program terminated.

ERROR # 353 - WARNING: Code overwritten. Code from the file written to already used location.

ERROR # 354 - Code in the file contains invalid data.

ERROR # 355 - Open File error

ERROR # 356 - Extension or file name error

ERROR # 357 - Wrong password for opening the image file

ERROR # 358 - Wrong PC hardware fingerprint # for opening the image file

ERROR # 359 - Image file ID error or file corrupted

ERROR # 360 - Check Sum of the Image file error or file corrupted

ERROR # 361 - Wrong header in the image file or file corrupted

ERROR # 362 - Image file is not for the MSP-GANG programmer.

ERROR # 363 - Image file contents error or file corrupted.

ERROR # 364 - Unknown protection mode of the image file or file corrupted.