slau358q.pdf - 第52页

Status Messages www.ti.com 52 SLAU358Q – September 2011 – Revised October 2019 Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated Operation ERROR # 067 - Unknown command. ERROR # 068 - Fa…

www.ti.com

Status Messages

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

==== Errors from the BOOT loader. ====

ERROR # 001 - BOOT Firmware only is in the MSP-GANG! The API Firmware should be downloaded.

ERROR # 002 - API Firmware CRC is not present! The API Firmware should be reloaded.

ERROR # 003 - API Firmware CRC error! The API Firmware should be reloaded.

ERROR # 004 - BOOT CRC error in the MSP-GANG!

==== Errors from the MSP-GANG Firmware. ====

ERROR # 010 - CRC Access key. Key corrupted. Access to programmer is blocked.

ERROR # 011 - Invalid programmer's access key. Access to programmer is blocked.

ERROR # 012 - Unknown interface.

ERROR # 013 - Vcc is too low.

ERROR # 014 - Vcc is too high.

ERROR # 015 - VtIO is too low.

ERROR # 016 - VtIO is too high.

ERROR # 017 - Header CRC. Image header is corrupted.

ERROR # 018 - Script CRC. Image script is corrupted.

ERROR # 019 - Exceed script number.

ERROR # 020 - Script command unknown.

ERROR # 021 - MCU Fetch synch failed.

ERROR # 022 - CPU JTAG synch failed.

ERROR # 023 - MCU device initialization failed.

ERROR # 024 - RAM firmware download failed.

ERROR # 025 - Flash blank check failed.

ERROR # 026 - Flash read verify failed.

ERROR # 027 - Flash write failed.

ERROR # 028 - Image flash write initialization failed.

ERROR # 029 - Image flash lock failed.

ERROR # 030 - Invalid script type/name.

ERROR # 031 - Script size too big.

ERROR # 032 - Used wrong MCU.

ERROR # 033 - IR communication failed.

ERROR # 034 - Page info number out of range.

ERROR # 035 - Address too high.

ERROR # 036 - Target number out of range.

ERROR # 037 - Address not even.

ERROR # 038 - Size not even.

ERROR # 039 - DCO calibration frequency out of range.

ERROR # 040 - DCO calibration failed.

ERROR # 041 - Gang flash write failed.

ERROR # 042 - SD Card - Read Response Error

ERROR # 043 - SD Card - Boundary Address Error

ERROR # 044 - SD Card - Initialization timeout

ERROR # 045 - SD Card - Read timeout

ERROR # 046 - SD Card - Initialization Error

ERROR # 047 - SD Card - CRC7 Error

ERROR # 048 - SD Card - CRC16 Error

ERROR # 049 - SD Card - Write CRC Error

ERROR # 050 - SD Card - Data Write Error

ERROR # 051 - SD Card - Write Timeout

ERROR # 052 - SD Card - MBR Sector Error

ERROR # 053 - SD Card - Volume Error

ERROR # 054 - SD Card - Address in File Error

ERROR # 055 - SD Card - Read File Error

ERROR # 056 - SD Card - File not found

ERROR # 057 - Hardware Rev-0. option not supported.

ERROR # 058 - Flash PSA verification failed.

ERROR # 059 - Flash read (Rx) data error.

ERROR # 060 - Vpp too low to secure fuse.

ERROR # 061 - Secure key incorrect.

ERROR # 062 - Secure device failed.

ERROR # 063 - Target not open, no access.

ERROR # 064 - BSL password wrong index.

ERROR # 065 - BSL read (Rx) timeout.

ERROR # 066 - BSL firmware download failed.

Status Messages

www.ti.com

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

ERROR # 067 - Unknown command.

ERROR # 068 - Fast BSL initialization failed.

ERROR # 069 - MSP-

GANG current overload. Reduce amount of target devices to 5 or select 30 mA output current.

ERROR # 070 - Wrong BSL passwords. Target cannot be unlocked.

==== Errors from the MSP-GANG DLL. ====

ERROR # 301 - Communication - Frame has errors !

ERROR # 302 - Unable to open COM port - already in use?

ERROR # 303 - Unable to close COM port !

ERROR # 304 - Unable to modify COM port state !

ERROR # 305 - Synchronization failed. Programmer connected?

ERROR # 306 - Timeout during operation - Correct COM port selected?

ERROR # 307 - Wrong baud rate specified !

ERROR # 308 - Communication Port baud rate change

ERROR # 309 - Communication port - diagnostic response error

ERROR # 310 - Open Comm port - invalid handle value

ERROR # 311 - Invalid Comm Port Setup

ERROR # 312 - Open Comm Port timeout

ERROR # 313 - Get Comm Port state error

ERROR # 321 - Command did not complete correctly !

ERROR # 322 - Command failed or not defined or Target not accessible !

ERROR # 323 - Could not read 'default.mspgangcfg'!

ERROR # 324 - File contains invalid record !

ERROR # 325 - Unexpected end of file !

ERROR # 326 - Error during file I/O !

ERROR # 327 - Selected file is of unrecognizable format !

ERROR # 328 - Unable to open file !

ERROR # 329 - Function argument(s) out of range !

ERROR # 330 - Note: Boot downloaded

ERROR # 331 - WARNING: Temporary function blocked, due to used main polling

ERROR # 332 - Image Memory corrupted or erased ! Load Image.

ERROR # 333 - Target not accessible !

ERROR # 334 - Verification failed !

ERROR # 335 - Main Process Parameters not yet set ! Load Image.

ERROR # 336 - Could not erase Image Buffer !

ERROR # 337 - Could not load Image Buffer !

ERROR # 338 - Could not load Main Process Parameters !

ERROR # 339 - Could not select Baud Rate !

ERROR # 340 - WARNING: Could not set target voltage -

Short circuitry or settling time too small?

ERROR # 341 - Invalid firmware command !

ERROR # 342 - Power supply voltage too low !

ERROR # 343 - WARNING: Sense voltage out of range - Check pin MSP_VCC_IN of target connector !

ERROR # 344 - Wrong target device connected !

ERROR # 345 - No target device connected

ERROR # 346 - File(s) contains already specified data (code overwritten)

ERROR # 347 - Selected Image number out of range

ERROR # 348 - Could not open the configuration file.

ERROR # 349 - Script Header size error

ERROR # 350 - Image ID error. Image ignored, program terminated.

ERROR # 351 - Image contents (size, no of tasks) error. Program terminated.

ERROR # 352 - Image CRC error. Program terminated.

ERROR # 353 - WARNING: Code overwritten. Code from the file written to already used location.

ERROR # 354 - Code in the file contains invalid data.

ERROR # 355 - Open File error

ERROR # 356 - Extension or file name error

ERROR # 357 - Wrong password for opening the image file

ERROR # 358 - Wrong PC hardware fingerprint # for opening the image file

ERROR # 359 - Image file ID error or file corrupted

ERROR # 360 - Check Sum of the Image file error or file corrupted

ERROR # 361 - Wrong header in the image file or file corrupted

ERROR # 362 - Image file is not for the MSP-GANG programmer.

ERROR # 363 - Image file contents error or file corrupted.

ERROR # 364 - Unknown protection mode of the image file or file corrupted.

www.ti.com

Self Test

SLAU358Q–September 2011–Revised October 2019

Submit Documentation Feedback

Operation

ERROR # 365 - Data offset in the image file error or file corrupted.

ERROR # 366 - Hex data conversion in the image file error or file corrupted.

ERROR # 367 - Image file corrupted.

ERROR # 368 - Image file cannot be unlocked

ERROR # 369 - Customized MCUs license file open error

ERROR # 370 -

WARNING: Code specified for the BSL space location, but access to the BSL is locked.

ERROR # 371 - Info memory page number is out of range.

ERROR # 372 - COM ports scan number is too low.

ERROR # 373 - Selftest data size too high.

ERROR # 374 - Data size too high.

ERROR # 377 - Gang mask ZERO. No target devices enabled. Nothing to do.

ERROR # 378 - Address definition.

ERROR # 379 - Data size is below 2.

ERROR # 380 - Invalid DCO number.

ERROR # 381 - Command not implemented.

ERROR # 382 - Wrong Target number

ERROR # 383 - Code File error.

ERROR # 384 - Password File error.

ERROR # 385 - Nothing to program/verify - empty code in selected memory space.

ERROR # 386 - Code out of range of the selected MCU.

ERROR # 387 - Invalid name index.

ERROR # 388 - Warning: Part of the code ignored. Check the memory setup.

ERROR # 391 - Image data size too long

ERROR # 392 - Terminated by user

ERROR # 393 - Code specified in the Retain Data space

ERROR # 394 - Number of tasks out of range

ERROR # 395 - Data blocks in all tasks out of range

ERROR # 396 - WARNING: Code from file is out of range in selected MCU.

ERROR # 397 - Option not supported for selected MCU.

ERROR # 398 - Wrong destination.

ERROR # 399 - The Address and Size of the Locking Options out of range.

ERROR # 400 - Warning - empty data or string.

ERROR # 401 - Invalid input parameter(s).

ERROR # 402 - Selected Image is READ ONLY and cannot be reprogrammed.

ERROR # 403 - Serial number location and code overlap.

ERROR # 404 - Serial number size error.

ERROR # 405 - No serial number found in serial number file.

ERROR # 406 - Serial number address or size error.

ERROR # 407 - Code located in the MPU-IPE space without selected access to MPU-

IPE in Memory Options.

ERROR # 408 - External Power Supply is required for selected MCU.

ERROR # 999 - Invalid error number !

2.4 Self Test

The MSP Gang Programmer Self Test program can test most of the hardware for correctness. Connect

the programmer to a computer running MSP Gang Programmer software. If using a Gang Splitter, connect

it to the MSP Gang Programmer hardware (this allows the Self Test to find short circuits in the Gang

Splitter). Disconnect all target devices, because any connected devices can modify the test results and

make them invalid.

Activate the Self Test by choosing the Tools→Self Test option from the drop-down menu. Press the Start

Self Test button, as shown in Figure 2-25, to begin. If the Self Test reports any problems then it is

advisable to send the test report to TI technical support for assistance.