Nordson_EFD_GV_Series_Operating_Manual - 第47页

GV Series Automated Dispensing Systems 47 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. Setting Passwor d Protection Use the Password …

GV Series Automated Dispensing Systems

46 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

Setting System Parameters (continued)

System Setup Screen Fields (continued)

Item Screen Capture Description

Auto Purge

Run Limit

Fluid Working

Life

To set up automatic purge settings, run limits, or ﬂuid working life limits

for a program, refer to “How to Set Up Auto Purge, Program Cycle

Limits, or Fluid Working Life Limits” on page82.

Other

• Pre-cycle Initialize: If checked, the robot always moves to the home

position (0, 0, 0) before the start of a dispense cycle.

• Needle XY Adjust: Enables or disables the Needle XY Adjust

capability. When Needle XY Adjust is checked, the Needle XY Adjust

button appears on the Program screen.

• Tip Detect Device: Indicates that the system includes the tip detector.

When Tip Detect Device is checked, the Needle Z Detect button

appears on the Program screen and the capability is enabled in the

Robot Initial Setup wizard. If unchecked, the capability is disabled in

the Robot Initial Setup wizard.

• 2D Code: Check this box to enable or disable QR code scanning

capability. Refer to “AppendixD, QR Code Scanning Setup” on

page134 to set up QR code scanning.

• Multi Needles: To dispense using more than one dispenser (up to four

dispensers possible), check this box. Refer to “AppendixE, Multi-

Needle Setup and Use” on page137 to set up a multi-dispenser

system.

• Height Sensor: If the system includes the optional height sensor,

check this box. Refer to “AppendixF, Height Sensor Setup and Use”

on page142 for all information related to the height sensor.

• Set Z to Focus: Sets whether the system captures the current

Zheight value in command windows. Refer to “Setting How the

System Captures Z Height Values (Optional)” on page 60 for details.

• Save Image (OptiSure AOI only): When checked, the system

automatically saves image ﬁles for applicable OptiSure AOI functions.

• Comment XYZ: When checked, any changes made to the tip height

(either the Tip Detect Device or Z Clearance settings on the System

Setup screen) will affect commands, even if a command is disabled.

• Image Stretch/Shrink: This system setting is useful if a workpiece

stretches or shrinks in size after extended use or after a process step

(such as baking). When this setting is checked, the system allows any

ﬁducial mark to adjust accordingly if a workpiece stretches or shrinks.

NOTE: The ﬁducial mark must still ﬁt within the camera’s ﬁeld of view,

which means there is a limit to how much stretching or shrinking the

system can accommodate.

Continued on next page

GV Series Automated Dispensing Systems

47www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

Setting Password Protection

Use the Password portion of the System Setup screen to set or reset a password. The purpose of a password is to

protect the system settings from unauthorized editing.

NOTES:

• The default is no password protection.

• If the password is forgotten, contact your Nordson EFD representative for assistance.

• A password is limited to 16 numbers or characters.

Click Step

• Click SYSTEM SETUP > OPEN.

• Under Password, enter a password or make the ﬁeld blank to

remove a password, then click CHANGE PASSWORD.

The system conﬁrms and immediately implements the

password change:

- If a password was entered, the system will prompt for the

password before opening the System Setup screen.

- If the Password ﬁeld was blank, no password will be required

to open the System Setup screen.

Item Screen Capture Description

Model drop-

down menu

Sets the dispensing software conﬁguration; this setting must match the

system conﬁguration (model). Any change takes effect upon software

restart.

Expert

For advanced users only.

Light (if

present)

• Default: Allows you to control the light intensity if an external switch is

used to control the light.

• Offset: When the system is in the CCD Mode, automatically changes

the light intensity based on the value entered.

NOTE: The Light settings are present only if an optional light accessory

is installed.

Setting System Parameters (continued)

System Setup Screen Fields (continued)

GV Series Automated Dispensing Systems

48 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

Setting Up and Calibrating the System (Required)

Before creating any programs or using the automatic offset update capabilities of the system, you must properly set

up and calibrate the system. Correct system setup and calibration is critical for proper system operation.

The Robot Initial Setup wizard guides you through the complete setup and calibration process. This process must

be performed at initial startup and also after any change to the system.

Examples of system changes include the following:

• Any time a component installed on the Zaxis (such as the syringe barrel or camera) is moved.

• Any time a dispensing tip or nozzle is changed.

Setup and calibration includes the following tasks:

• Verifying the robot model and tip detector selection

• Opening the robot initial setup wizard and focusing the camera

• (Only GV systems with a tip detector) setting up the tip detector*

• Setting the camera-to-tip offset

• Setting a mark

• Setting the camera scale*

• Setting the tip-to-workpiece offset*

• (Only GV systems with a tip detector) testing the system setup and calibration

• (Only GV systems without a tip detector) testing the system setup and calibration

*All required setup and calibration tasks are guided by the Robot Initial Setup wizard. However, the tasks shown above with

an asterisk (*) can be performed individually as needed. Refer to “AppendixB, Non-Wizard Setup Procedures” on page124

for the procedures.

NOTE: Refer to “About Offsets” on page27 for an explanation of offsets.

Verifying the Robot Model and Tip Detector Selection

Click Step Reference Image

• Click SYSTEM SETUP > OPEN.

• Under Other, verify the following:

- If your system includes a tip detector, Tip

Detect Device is checked.

- The correct robot model is shown. If

the robot model is not correct, go to

“Changing the Robot Model Selection”

on page57 to select the correct model.

Return here to continue.

• If you made changes, close and reopen the

DispenseMotion software for the changes to

take effect.

• Continue to “Setting Up the System

Using the Robot Initial Setup Wizard” on

page49.