Nordson_EFD_GV_Series_Operating_Manual - 第63页

GV Series Automated Dispensing Systems 63 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. Pr ogramming This section provides how-to proc…

100%1 / 150
GV Series Automated Dispensing Systems
62 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Setting the Units of Measure
By default, the system displays units of measure using the metric system. Follow this procedure to change how the
system displays units of measure.
# Click Step Reference Image
1
> >
• Click SYSTEM SETUP > OPEN >
EXPERT.
2
11111111 >
• Enter 11111111, then click OK.
3 • Click CONTROL.
4
>
• In the Expert window, select the
desired unit of measure under System
Unit.
• Click OK to save the setting.
The system automatically exits the
software to allow the change to take
effect.
Restoring the System to the Factory Default Settings
To restore all settings to their factory default values, open and then close the following file located on the D:\ drive:
D:\ever_sr\Initial Setup.
GV Series Automated Dispensing Systems
63www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Programming
This section provides how-to procedures for the most commonly performed programming tasks. Refer to “How to
Create and Run a Program” for an example of how to use the dispensing software to create a complete program. If
you have difficulty creating a program for your application, contact your Nordson EFD representative. Before using
this section:
• Complete all applicable installation tasks. Refer to “Installation” on page19.
• Complete all required setup tasks. Refer to “Setup” on page44.
• Refer to “Concepts” on page26 for important robot programming concepts and for an overview of the
dispensing software screens and icons.
How to Create and Run a Program
The procedure provides the basic steps for creating and running a program. Every program is different. Use these
basic steps and refer to “How to Create Patterns” on page66 and “AppendixA, Command Function Reference”
on page98 to create the desired application pattern for the workpiece or group of workpieces.
PREREQUISITES
The system is properly set up. Refer to “Setting Up and Calibrating the System (Required)” on page48.
If the tip or any element of the Zaxis head was changed, repeat system setup and calibration using the Robot
Initial Setup wizard. Refer to “Setting Up the System Using the Robot Initial Setup Wizard” on page49.
The system is in the correct mode (Tip or CCD).
A workpiece is properly positioned on the fixture plate.
# Click Step
1
• Click the PROGRAM tab.
Address 1 is available to insert a command.
2
• Jog the dispensing tip to a desired XYZ location by clicking the navigation
icons.
3
• Insert a setup or dispense command that tells the robot what to do. Click
a command icon, or double-click anywhere in the address line to select a
command from the drop-down menu.
4
• Edit the command parameter settings. Refer to the following sections of this
manual for information to help you create programs:
- “About Programs and Commands” on page26 (includes best practices)
- “How to Create Patterns” on page66
- “How to Create a Mark” on page70
- “AppendixA, Command Function Reference” on page98 (provides
detailed information on all commands)
5
• Repeat steps 2 through 4 until the program is complete.
6
• To delete a command, click the command and then click the Delete icon.
7
• Click END PROGRAM to end the program.
Continued on next page
GV Series Automated Dispensing Systems
64 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
# Click Step
8
or
• Click VIEW or RUN to test the program and make adjustments until the
program runs correctly.
NOTE: VIEW runs a program by tracing it with the camera, without
dispensing fluid. RUN runs the actual program, including dispensing.
9
>
• Click A NEW FILE.
• Click SAVE. If the file is not already named, enter a name for the file.
• Click YES/OK when prompted for confirmations.
How to Create and Run a Program (continued)
How to Add Comments to a Program
You can add your own comments to any command address line in a program.
PREREQUISITES
The program you want to add comments to is open.
#
Click Step Reference Image
1
• Select a blank command address line.
NOTE: Comments must be entered on a
blank line. If you try to enter a comment on a
line that includes a command, you will disable
the command.
2
>
>
• Click DISABLE ADDRESS.
• Enter your comment in the Enter Comment
window.
• Click OK to save.
3
>
• To delete a comment, select the comment
and then click DELETE.