00198168-02_Technical_Training_TX-Series_EN - 第126页

5 Placement Heads 5.2 C&P20 P/M2 Head 126 Technical Training SIPLACE TX-Series 10/2016 Maintenance task Twin Interval Equipment required Exchanging the aperture ring (vacuum pump) Workflow 2 ● Cleaning Wipe, KM-Wipe …

5 Placement Heads

5.2 C&P20 P/M2 Head

Technical Training SIPLACE TX-Series 10/2016 125

No. Code Error Description Possible Cause Action

9 30524 Cannot reference DP

axis, segment:

DP drive defect

●

Inspect DP drive and

replace it if necessary

●

Check error chain

messages

10 30573 Skipping segment after

positioning error,

segment:

●

DP drive high

temp

●

DP drive defect

●

Try to enable relevant DP

drive, Inspect DP drive and

replace it if necessary

●

Check error chain

messages

11 30624 Nozzle scan failed

●

Dirty nozzle

●

Air kiss too low

●

Inspect nozzle and replace

it if necessary

●

Check error chain

messages

●

Check air kiss circuit

34401 Cannot scan nozzle

33368 Nozzle scanning

unsuccessful

5.2.9.2 Maintenance

Maintenance task Twin Interval Equipment required

Cleaning the return cylinder Workflow 2

●

Cleaning Sticks

●

Universal placement head mounting rack

Cleaning the Z Axis Workflow 2

●

Anti-static tweezers, Bernstein 5-192

●

Torque Screwdriver ESD 1,0-5,0 Nm

●

Hexagon Socket Head CAP Screw Driver

●

Universal placement head mounting rack

●

silicone hose D12 L20mm

●

Allen key insert - 2,5

Lubricating the DP segment

guidance

Workflow 2

●

Cleaning Wipe, KM-Wipe

●

Lubcon Thermoplex ALN 1001/00, 50ml (blue)

●

Cleaning Sticks

●

Multipette M4

●

Combitips advanced 0,1 ml blue

Lubricating the Z Axis linear

guidance

Workflow 2

●

Cleaning Wipe, KM-Wipe

●

Lubcon Thermoplex ALN 1001/00, 50ml (blue)

●

Cleaning Sticks

●

Universal placement head mounting rack

●

Multipette M4

●

Combitips advanced 0,1 ml blue

●

silicone hose D12 L20mm

Lubricating the C&P20P DP

drive bearing

Workflow 2

●

Cleaning Wipe, KM-Wipe

●

Klueberalfa DH 3-100, 50ml (black)

●

Cleaning Sticks

●

Universal placement head mounting rack

●

Multipette M4

●

Combitips advanced 0,1 ml black

Cleaning the DP reflection

area

Workflow 2

●

Isopropanol

●

Cleaning Sticks

5 Placement Heads

5.2 C&P20 P/M2 Head

126 Technical Training SIPLACE TX-Series 10/2016

Maintenance task Twin Interval Equipment required

Exchanging the aperture ring

(vacuum pump)

Workflow 2

●

Cleaning Wipe, KM-Wipe

●

Universal placement head mounting rack

●

Torque Screwdriver ESD 0,1-0,6 Nm

●

Allen key insert wiha - 2,5

●

Cover pre-assembled C&P20P

●

Orifice plate pre-assembled C&P20 P

Cleaning and lubricating the

race way

Workflow 2

●

Lamora D 220

●

Cleaning Sticks

●

silicone hose D12 L20mm

●

Torque Screwdriver ESD 0,1-0,6 Nm

●

Allen key insert wiha - 2,5

●

Cover pre-assembled C&P20 P

Cleaning the component

sensor

Workflow 2

●

Isopropanol

●

Cleaning Sticks

●

Universal placement head mounting rack

●

Protective cover CO sensor C&P20 P

Replacing the filter discs Workflow 2

●

Universal placement head mounting rack

●

Filter disc removal device /C&P20 P

●

Filterdisc kpl. C&P20 P

●

Nozzle 4245 Calibration nozzle

Remove maintenance label,

clean this area and attach

new label with actual date

Workflow 2

●

Cleaning Wipe, KM-Wipe

●

Isopropanol

●

Maintenancelabel C&P20 P 10 pcs.

●

CD-marker edding 8400

●

Point Pliers 140mm OVAL

For detailed information refer to the Maintenance Job Card for C&P20P Heads.

5 Placement Heads

5.2 C&P20 P/M2 Head

Technical Training SIPLACE TX-Series 10/2016 127

5.2.10 Excercise: C&P20 P Head

1. During reference run the difference between open/close vacuum values for segment 2

is too low, what could be the possible reason?

A PRV is defective.

B Holding circuit vacuum is soiled.

C The nozzle soiled or wrong type.

D Holding circuit vacuum measurement board is defect.

2. Which of the following describes best the function of the component sensor?

A To measure the nozzle height.

B To monitor the presence and/or component height after pickup and before placement.

C To determine Z Axis movement.

D All of the above.

3. Which of the following is false?

A The function of the retract unit is to prevent the Z Axis from sliding down and getting dam-

aged after power off

B The Z Axis end signal is triggered by bottom light sensor, no matter what placement mode

for CPP Head.

C The function of the component camera is component recognition and to determine the exact

position of component on nozzle

D The function of the PRV is to supply vacuum and air kiss during Pickup/Place process.

4. What are the differences between C&P20 P and C&P20 M2

………………………………………………………………………………………………………