00192216-01.pdf - 第41页

SIPLACE 80 S-20 / S-23HM/ F4 / F4-6 / F5 2 Retrof itting Instructions for Ceramic S ubstrate Centering Unit (Optional) 04/2000 Issue 2.2 Safety Instructions 41   'HI LQL WLRQ V DANGER in term s of th ese ins tr…

2 Retrofitting Instructions for Ceramic Substrate Centering Unit (Optional) SIPLACE 80 S-20 / S-23HM/ F4 / F4-6 / F5

2.2 Safety Instructions 04/2000 Issue

2.2 Safety Instructions

DANGER

Only Siemens service engineers are permitted to perform this retrofitting of the ceramic substrate

centering unit .

Comply with the higher ranking safety notes in Chapter "Operational Safety" in the User Manual

and Service Manual.

These SIPLACE machines are powered by 120V / 208V +/- 5% (US version) or 3 x 230V/400V

+/-5% 50/ 60 Hz line voltage.

Portions of the system are therefore conducting dangerous electricity - inside the machine even

while the master switch is turned off.

The machine has to be switched OFF and disconnected from the mains before you perform any

work. In addition, the compressed air supply must be turned off at the main valve of the com-

pressed air unit in the machine frame and the compressed air lines must be bled by actuating the

needle valve on the compressed air unit (particularly due to the risk of injury - posed by residual

air - at the pneumatic cutter).

When a dual conveyor is involved, there is a risk of having a body member pinched or crushed

between the fixed side of conveyor 1 and the movable side of conveyor 2 when the conveyors are

travelling at maximum width.

With all of these SIPLACE machines the Y-gantry must always be moved / pushed out

of the area of the component changeover table before changing tables.

Otherwise there will be a risk that the placement head may crash !!

Obey the applicable accident prevention regulations, DIN standards and special safety codes of

your country at all times. DIN EN 60204 must be adhered to during all work inside the machine.

Follow the instructions regarding residual voltages in Chapter "Operational Safety"

Comply with regulations on ESDs (see Chapter "Operational Safety"), e.g., when working on the

conversion PCB for the PCB conveyor control.

During the work of retrofitting secure the machine conscientiously against other personnel and

prevent it from being turned back on without authorization, as described in the Operator’s Manual

in the chapter "Locking the Machine...".

There is additional, higher risk of accident when working with the SITEST program.

The SIPLACE program is only to be started by personnel who are authorized to do so.

For the work with the SITEST program the component changeover table must be moved in and

correctly connected. 

SIPLACE 80 S-20 / S-23HM/ F4 / F4-6 / F5 2 Retrofitting Instructions for Ceramic Substrate Centering Unit (Optional)

04/2000 Issue 2.2 Safety Instructions

 'HILQLWLRQV

DANGER

in terms of these instructions means that death, severe bodily injury or considerable material dam-

age WILL occur if the instructions about danger are not followed.

WARNING

in terms of these instructions means that death, severe bodily injury or considerable material dam-

age may occur if the warnings are not heeded. 2

CAUTION

in terms of these instructions mean that minor bodily injury or material may occur if the cautions

are not heeded. 2

NOTE

in terms of these instructions is a statement of important information about the product or the

pertinent portion of the instructions to which particular attention is being drawn. 2

2 Retrofitting Instructions for Ceramic Substrate Centering Unit (Optional) SIPLACE 80 S-20 / S-23HM/ F4 / F4-6 / F5

2.3 Retrofit Kit, Tools 04/2000 Issue

2.3 Retrofit Kit, Tools

 5HWURILW.LW

Ceramic substrate centering unit for the SIPLACE PCB Handling,

item no.: 00116814-02, type 2, consisting of:



- Rocker with clamping element, installed (for movable conveyor side)

- Holddown with rocker actuator, installed (for movable conveyor side)

- Guide, short

- Holddown for stationary conveyor side

- Guide assembly, RH side (fasten with the screws previously removed)

- Slide assembly, X-direction, incl. proximity switch and compressed air connection

- Cable for proximity switch, with connector

- Cable for solenoid valve, with solenoid valve connector

- Compressed air hose

- Valve for ceramic substrate centering unit (required when installing a 2nd centering unit)*

*) As standard, there is a solenoid valve on the back of the compressed air unit (see Fig.

2.4.4).

- Green plastic rail

Used if the substrate is only to be centered in the Y-direction.

NOTE:

The components indicated under "Additional Material Required" are not included in the retrofit kit.



 $GGLWLRQDO0DWHULDO5HTXLUHG

3HUFHUDPLFVXEVWUDWHFHQWHULQJXQLW 

– AMPMODU contact BU 0.12 - 0.56 mm item no. 00304845 2 each per solenoid valve

and 2 each per proximity

switch

– AMPMODU connector Bu 2 x 3-pin *) item no. 00304916 1 each per solenoid valve

and per proximity switch

– AMP LATCH coding pin *) item no. 00304910 1 each per solenoid valve

and per proximity switch

– Cable tie L x W = 140 x 3.6 mm item no. 00805141-01 5 - 6 units