SM421 Maintenance Reference(Chi Ver1)_866B5 - 第118页
7-17 输入 & 输出 (INPUT/ OUTPUT) PIN N O. D EF. DESCRIPTION 1 CA NH CAN 通信信号 2 CANL 其它 NODE 的 CAN 通信 信号 连接 3 /IO-RES RESET M CAN MASTER 信号 FRO CN2/C N3 A/D 用 + CAN MASTER 6 +12V 12V 电源 FROM 1 24VP OUTPUT PO 源 后供电 …
Samsung Component Placer SM421 Maintenance Reference
基板状态诊断LED信息
LED ON DESCRIPTION Remark LED ON DESCRIPTION Remark
LED1
Can
LED6
(24V)
发信
基板输出电源
2
出现Error
LED7
基板动作电源
3
Can 收信
LED27 Side ILL Up S
4
CPU 收信
LED28 Side ILL Down
5 IO RESET
Con or Control Bo
接 受 veyor 与 输入及操作面板开关
Board
、以
CAN Master Board
ignal Light动作。
的命令后，使Conveyor、ANC及相关
使用的电源
外部 源: +24V DC
部 源: +5V DC
要
输入电
内 使用的电 / +24V DC
主 功能说明
LED
(5V)
LED
ensor Input
LED
Sensor Input
LED
7.3.5. vey ard
Con ANC的传感器 的输入 后 传 输 给 CAN Master
；接收 Solenoid Valve
及S
7-16
7-17
输入&输出 (INPUT/OUTPUT)
PIN NO. DEF. DESCRIPTION
1 CANH
CAN 通信信号
2 CANL
其它NODE的CAN通信信号连接
3 /IO-RES
RESET
M CAN MASTER
信号
FRO
CN2/C
N3
A/D用 +
CAN MASTER 6 +12V
12V 电源
FROM
1 24VP
OUTPUT PO
源
后供电
RT用 DC+24V 电
输入READY SW
2 24V
INPUT 源 生成BOARD电源DC+5V PORT用 DC+24V 电
CN4
DC+24V
3/4 24G
电源 GROUND
-
3 IN1.0 PCB INPUT SENSOR
4 IN1.1 PCB WAIT SENSOR
9 IN1.2
DUM
INP
P C
UT
ONVEYOR FULL
10 IN1.3
DUMP CONVEYOR
INPUT
BUSY
15 IN1.4 PCB PLACE SENSOR
16 IN1.5 PLACE STOPPER UP SENSOR
21 IN1.6
PLACE
SENSO
STOPPER DOWN
R
CN14
SECON
24PIN CONNECTOR(在3段C/V时不
使用WAIT STOPPER UP/DOWN传
)
22 IN1.7 D PLACE SENSOR
感器
3 IN2.0 BUT UP SENSOR
4 IN2.1 BUT DOWN SENSOR
9 IN2.2 HOLE FIXER RIGHT SENSOR
10 IN2.3 HOLE FIXER LEFT SENSOR
15 IN2.4 RESERVED INPUT PORT
16 IN2.5 RESERVED INPUT PORT
21 IN2.6 RESERVED INPUT PORT
CN15
RESER
NNECTOR
22 IN2.7 VED INPUT PORT
24PIN CO
3 IN3.0 PCB OU SOR T SEN
4 IN3.1 RESERVED INPUT PORT
9 IN3.2 RESERVED INPUT PORT
10 IN3.3
ANC1 S OSE
SENSOR
HUTTER CL
15 IN3.4
ANC1 S
SENSOR
HUTTER OPEN
16 IN3.5 RESER PUT PORT VED IN
21 IN3.6 RESER T PORT VED INPU
CN16
SER RT
24PIN CONNECTOR(在3段C/V时不
OPPER UP/DOWN传
感器)
22 IN3.7 RE VED INPUT PO
使用OUT ST
3 IN4.0 FRONT GENCY INPUT EMERCN17
4 IN4.1 FRONT DOOR INPUT
24PIN CONNECTOR
Samsung Component Placer SM421 Maintenance Reference
PIN NO. DEF. DESCRIPTION
9 IN4.2
CHA . FFEEDER NGE SW
INPUT
IN4.3 RE PU
IN4.4 START SW T
IN4.5 STOP SW
IN4.6 RESET SW T
IN4.7 POWER O
10 ADY SW. IN T
15 . INPU
16 . INPUT
21 . INPU
22 N INPUT
3 IN5.0 REAR EMERGENCY INPUT
4 IN5.1 REAR DOOR INPUT
9
CHANGE SW
IN5.2
RFEEDER
INPUT
.
CONNEC
10 IN5.3
FRONT OPERATION STATUS
INPUT
15 IN5.4
REAR OPERATION STATUS
INPUT
16 IN5.5
MAIN AIR SENSOR
21 IN5.6 REAR SO
FRO
RESERVED OU
CN18
22 IN5.7 NT SO
24PIN TOR
3 OUT1.0 TPUT
4 OUT1.1 PLACE STOPPER SOL PORT
9 .2 OUT1 BUT SOL
HOLE FIXER SOL
EDGE PUSHER SOL
10 OUT1.3
15 OUT1.4
16 OUT1.5 RESERVED OUTPUT PORT
21 OUT1.6 ANC1 SHUTTER SOL
CN5
22 OUT1.7 RESERVED OUTPUT PORT
24PIN CONNECTOR
3 OUT2.0 RESERVED OUTPUT PORT
4 OUT2.1 READY SW. LAMP OUT
9 OUT2.2 START SW. LAMP OUT
10 OUT2.3 STOP SW. LAMP OUT
15 OUT2.4
RFEEDER CHANGE SW. LAMP
OUT
16 OUT2.5
FFEEDER CHANGE SW. LAMP
OUT
21 OUT2.6 RESET SW. LAMP OUT
CN6
22 OUT2.7 READY RELAY OUTPUT
24PIN CONNECTOR
1 OUT3.0 RED LAMP OUTPUT
2 OUT3.1 BLUE LAMP OUTPUT
3 OUT3.2 GREEN LAMP OUTPUT
CN7
4 OUT3.3 RESERVED OUTPUT PORT
6PIN CONNECTOR
CN8 1/3 OUT3.4 FRONT BELT CONTROL 6PIN CONNECTOR
7-18