WPC an:on SIPLACE SX1:SX2 Montageanleitung : Assembly Instructions - 第44页
Contents 5 Appendix .. 69 5.1 Excerpts from the Service Manual .. 69 5.1.1 Downholder .. 69 5.1.1.1 Fitting the Downholder .. 70 5.1.2 Setting the DIP Switch on the CAN Switch .. 76 5.1.3 CAN bus terminator for…
Contents
Contents
1 Introduction.. 45
1.1 Safety instructions.. 45
1.1.1 Conventions for the use of safety instructions and symbols.. 45
1.1.2 Safety instructions for working with strong magnetic fields.. 46
1.1.3 Safety instructions for the power supply (without SMPS).. 46
1.1.4 Safety instructions for the power supply (with SMPS).. 48
1.1.5 Safety instructions for the compressed air supply.. 50
1.1.6 Safety instructions for work on the cutting device.. 50
1.1.7 Safety instructions for the gantry.. 51
1.2 Preparatory work..... 51
1.3 Notes on switching the machine back on.. 53
1.4 Other instructions.. 53
1.4.1 Environmentally-friendly disposal of materials and components.. 53
1.4.2 Use of original accessories and spare parts.. 53
1.4.3 ESD guidelines.. 54
1.4.3.1 What does ESD mean?.. 54
1.4.3.2 Important measures to protect against static charging.. 54
1.4.3.3 Handling ESD modules.. 54
1.4.3.4 Measurements and modifications to ESD modules.. 54
1.4.3.5 Dispatching ESD modules.. 55
1.4.4 Validity of Document.. 55
1.4.5 Release History.. 56
1.5 Staff qualifications and training.. 56
2 Brief description.. 57
2.1 Overview of WPC5/WPC6.. 57
2.1.1 Overview of the Modules.. 57
2.2 Overview of WPC5/6 COT Insert.. 58
2.3 Scope of Delivery.. 58
2.4 Tools and Equipment Required.. 58
3 Setting up and Commissioning.. 59
3.1 Removing the Standard Component Trolley Feed Device.. 59
3.2 Installation of the CAN switches with two WPCs.. 60
3.3 Installing the Component Trolley Feed Device for the WPC5.. 62
4 Operator Tasks.. 65
4.1 Docking the WPC5/WPC6.. 65
4.2 Switch on the WPC5/WPC6.. 66
4.3 Undocking the WPC5/WPC6.. 67
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 43
Contents
5 Appendix.. 69
5.1 Excerpts from the Service Manual.. 69
5.1.1 Downholder.. 69
5.1.1.1 Fitting the Downholder.. 70
5.1.2 Setting the DIP Switch on the CAN Switch.. 76
5.1.3 CAN bus terminator for CO table [03046863-xx].. 77
5.1.4 Replacing the Waste Tape Chute.. 78
5.1.5 Disabling the compressed air supply.. 78
44 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
1 Introduction
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 45
1 Introduction
This manual describes the replacement of the standard feed device with the WPC5 feed device on SI-
PLACE® SX1/SX2 machines. (WPC = Waffle Pack Changer).
1.1 Safety instructions
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
1.1.1 Conventions for the use of safety instructions and symbols
Safety information
This document contains notes that must be observed to guarantee your personal safety and to avoid
damage to equipment. These notes are highlighted by warning triangles and are indicated as follows
according to the level of risk:
DANGER
Definition
For the purposes of this document, this indicates that fatal or severe injuries or considerable damage
to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this document, this indicates that fatal or severe injuries or considerable damage
to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this document, this indicates that minor injuries or damage to property may occur
if this caution is not observed.
NOTICE
Definition
For the purposes of this document, this note provides information about the product or indicates a
part of the document that requires particular attention.
Symbols
Example Description
Next This typeface marks controls and interface elements in the software.
► This symbol indicates actions that have to be performed by the operator.
[01234567‑xx] Article numbers are indicated by square brackets.