WPC an:on SIPLACE SX1:SX2 Montageanleitung : Assembly Instructions - 第61页
3 Setting up and Commissioning Mo nt ag ea nl ei tu ng / A ss em bl y In st ru ct io ns W PC a n/ on S IP LA CE S X1 /S X2 - 0 3/ 20 25 61 Installation Fig.12: Connecting the CAN switch ► Disconnect the CAN bus (1) insi…
3 Setting up and Commissioning
60 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
Fig.10: Mounting tool (example of X-Series shown)
1. Mounting tool
2. Eyelet
3. Fastening screws for mounting tool
4. Fastening screws for COT insert
CAUTION!
Heavy machine part!
The COT insert is heavy. To lift it out, you
will need to use the fit-up aid and a suit-
able lifting device.
.
► Attach the mounting tool to the fixtures provided on the COT insert.
► Remove the six screws fastening the COT insert.
► Fix the lifting device to the eyelet of the mounting tool.
NOTICE
Positions
The COT insert can be installed at different positions (inner/outer) in the machine location. Mark the
position of your COT insert, to ensure that this is subsequently returned to its original position.
► Lift the complete COT insert out of the machine and place it on a suitable surface (e.g. four
wooden blocks).
► Make sure that you do not damage any valves, connection cables, hoses etc.
See also
2 1.2 "Preparatory work..." [}51]
3.2 Installation of the CAN switches with two WPCs
Overview
Fig.11: CAN switch with cable
Upgrade Kit COT-I-30 CAN Switch for 2nd
WPC [03085518-xx]
In case of two WPCs operating on one machine
the installation of a CAN switch on each loca-
tion is required.
3 Setting up and Commissioning
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 61
Installation
Fig.12: Connecting the CAN switch
► Disconnect the CAN bus (1) inside the in-
frastructure box at point X1_2.
► Set the DIP switches on the CAN-switch
(see 5.1.2 "Setting the DIP Switch on the
CAN Switch" [}76]).
► Plug the CAN switch (2) between the two
cables. Move the stud and screws in a
way, that each connector is fixed with at
least one screw on the CAN switch.
Fig.13: Connecting the power supply
► Connect the power supply to the 9‑pin
connector X112 (location1) or X132 (loca-
tion2). Make sure that both pins engage
correctly. Tug gently on the cable to
check.
► Make sure that the cables are stowed cor-
rectly inside the infrastructure box and
fasten them with cable ties.
► Repeat the installation of the CAN switch
on the second location.
3 Setting up and Commissioning
62 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
Fig.14: Detailed circuit diagram CAN switch
► Set the DIP switches on the "CAN-Bus terminator component table" [03046863-xx] (see 5.1.3
"CAN bus terminator for CO table [03046863-xx]" [}77]).
3.3 Installing the Component Trolley Feed Device for the WPC5
► Dismantle the bracket for checking the table height on the right and left hand side. For more infor-
mation, read section 5.1.1 "Downholder" [}69].
Fig.15: Angle plate (here: left)
The angle plates (1) on the left and right must
be fixed in the outermost position.
► If the angle plates are in the innermost
position, move them to the outermost posi-
tion (3). To do this, loosen the three
screws (2) fastening the angle plates and
then fix the plates in the outermost posi-
tion.
NOTICE!
When using the WPC5, the angle plates
must always be fitted in the outermost
position! You may need to move them to
the outermost position if they are not
already there.
.