00198536-02_AI_Mixed-Mode_TX2iV1_TX2V2_de_en - 第114页
4 Appendix 4.1 Excerpts from the Service Manual 114 Assembly Instructions / Montageanleitung SIPLACE TX2i V1 SIPLACE TX2 V2 Option Mixed-Mode 01/2019 Adjustment DANGER Strong permanent magnet fields Observe the safety in…
4 Appendix
4.1 Excerpts from the Service Manual
Assembly Instructions / Montageanleitung SIPLACE TX2i V1 SIPLACE TX2 V2 Option Mixed-Mode 01/2019 113
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
CAUTION
Installation instructions
► Set the switch on the nozzle changer to 2-3 (valid for all SIPLACE TX machines).
► Check the mechanical installation height of the nozzle changer (see 4.1.2.4.1 "Setting
the Nozzle Changer Height" [}113]).
4.1.2.5 "Jumpers on the Nozzle Changer" [}115]
Setting the Nozzle Changer Height
Parts, equipment and tools
●
Measuring scale
●
NC shim plate (0.3mm) [03021079-xx]
Overview
Fig.63: Overview of measurement procedure
1. Measuring scale
2. Top edge of the X axis upper linear
guide
3. Values to be set (277 +/- 0.2 mm)
4. Nozzle changer contact surface
NOTICE!
Alternatively, you can measure from
the top edge of the lower guide rail of
the gantry. In this case the distance is
116.0+/‑0.2mm.
.
CAUTION!
Only with mixed mode option
If applicable, observe the deviating
measurements for the mixed mode op-
tion:
Installation height of NC:
280.65 +/ 0.2 mm
Measured from the upper edge of the
top linear guide
OR
119.65 +/ 0.2 mm
Measured from the upper edge of the
bottom linear guide
See also the assembly instruction
manual "Option Mixed Mode –
SIPLACE TX2i" [00198536‑xx]
.
4 Appendix
4.1 Excerpts from the Service Manual
114 Assembly Instructions / Montageanleitung SIPLACE TX2i V1 SIPLACE TX2 V2 Option Mixed-Mode 01/2019
Adjustment
DANGER
Strong permanent magnet fields
Observe the safety instructions in section 1.1.2 "Safety instructions for working with strong
magnetic fields" [}74].
► Remove the nozzle changer.
4.1.3.4 "Replacing the Nozzle Changer" [}126]
4.1.2.4 "Replacing the Nozzle Changer" [}112]
► During the following inside measurement make sure that the tip of the measuring scale does
not touch the magnetic strip as this might scratch it!
CAUTION
Strong magnetic forces
Place a suitable plastic plate between the magnet and measuring scale, if required.
► Position the measuring scale(1) on the top edge of the X axis upper linear guide(2) and
measure the distance to the nozzle changer contact surface(4).
► Hold the measuring scale vertically.
► The setting value (3) is 277+/‑0.2mm.
(Deviating values for Mixed Mode option, see above.)
You can adjust the height, where necessary, by removing or adding NC shim plates.
CAUTION
Crash hazard!
Do not place too many shim plates underneath.
► Calibrate the position of the nozzle changer.
4 Appendix
4.1 Excerpts from the Service Manual
Assembly Instructions / Montageanleitung SIPLACE TX2i V1 SIPLACE TX2 V2 Option Mixed-Mode 01/2019 115
4.1.2.5 Jumpers on the Nozzle Changer
Overview
Fig.64: Jumpers on the Nozzle Changer
1. Jumper X10
The jumper X10 needs to be set at the fol-
lowing nozzle changers:
●
Nozzle changer basic structure CPx/all
assembly - short [03103649-xx]
●
Nozzle changer basic structure CPx/all
assembly - long [03103514-xx]
Preparation
NOTICE
Before installation
Due to the design, this setting must be performed before installation in the machine.
► If the new nozzle changer is being fitted as a spare part in a machine with I/O module
control, you will need to reconnect the jumper to pin 1-2.
Fig.65: Checking the I/A module control
To check whether the machine has I/O mod-
ule control, proceed as follows:
► Switch over to the operator level Ser-
vice.
► Click the
button.
► Click on the Embedded software but-
ton.
► Click the Update subsystem button.
► If an I/O module control is present, you
will see the entry Nozzle Changer at I/
O Module.
Setting
► Set the correct value on the jumper for your head type, software and control method.
Jumper X10
Head SW <= 706.x SW >= 707.x
I/O controller XFCU I/O controller XFCU
CPx, DLM 1-2 1-2 1-2 2-3
C&P20P --- --- --- 2-3 (factory settings)