4OM-1626-001_w.pdf - 第106页
4OM-1610 2-3 2. Management Informatio : Chap.2 091 1-001 • Remedial Procedure from “Management Information” Window (1) Make a note of the management information. Notice If you forget the Management Information, correct …
4OM-1610
2-2
2. Management Information : Chap.2
2. Management Information
2.1 "Management Information" Window
When normal recovery does not occur after a mistake in the machine operation or
an error, the following management information window appears.
[1]
[4]
[3]
[2]
[5]
Example of Management Information F4B2
[1] Management Information
In this window, the management information is displayed.
[2] Management Information Code
In this window, the management information code is displayed.
[3] Display Area A
The outline of the management information is displayed in this area.
[4] Display Area B
The details of the management information are displayed in this area.
[5] [OK] Button
When this button is pressed, the window displayed just prior to the
"Management Information" is returned.
0911-001
4OM-1610
2-3
2. Management Informatio : Chap.2
0911-001
•
Remedial Procedure from “Management Information” Window
(1) Make a note of the management information.
Notice
If you forget the Management Information, correct recovery can not be
performed. Therefore, make sure to make a note.
(2) Press the [OK] button to return the original window.
(3) Perform the correct recovery based on the Management Information.
4OM-1610
2-4
2. Management Information : Chap.2
2.2 Management Information List
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
010101 Emergency Stop
Press [POWER ON] button to activate Load Power circuit.
010103 Emergency Stop
Emergency Stop switch is pressed. Please cancel it.
010201 Air Pressure Drop
Detection of Air Pressure Drop is detected
010401 Safety cover lock conrm
Please close and lock the safety cover.
010402 Safety cover lock conrm
Operate after close and lock the safety cover. (LED on)
010403 Safety cover lock conrm
Operate after close and lock the safety cover.
010503 Beam XY main loop OFF
Beam XY main circuit Error
010801 Feeder base conrm (Rear)
Set the feeder cart (rear) and connect cable.
010802 Feeder base conrm (Rear)
Detect elevator unit (rear).Operate after remove elevator .
010803 Feeder base conrm (Rear)
Could not detect elevator unit (rear). Connect elevator unit and operate by "unit
exchange menu".
010804 Feeder base conrm (Rear)
Disconnect elevator unit (rear). Check connector.
010805 Feeder base conrm (Rear)
Feeder cart (rear) is not upper position. Push feeder ready sw.
010806 Feeder base conrm (Rear)
Push feeder ready sw.
010807 Feeder base conrm (Rear)
Feeder base power or Feeder power is "OFF". Please press "Feeder Ready"
switch(Rear), and put it up again after putting Feeder Cart(Rear) down.
010901 Feeder base conrm (Front)
Set the feeder cart (front) and connect cable.
010902 Feeder base conrm (Front)
Detect elevator unit (front).Operate after remove elevator .
010903 Feeder base conrm (Front)
Could not detect elevator unit (front). Connect elevator unit and operate by "unit
exchange menu".
010904 Feeder base conrm (Front)
Disconnect elevator unit (front). Check connector.
010905 Feeder base conrm (Front)
Feeder cart (front) is not upper position. Push feeder ready sw.
010906 Feeder base conrm (Front)
Push feeder ready sw.
0911-001