00196478-08_MM_SX12DX12_en - 第54页
Major Maintenance Maintenance Tasks for the Componen t Feed Device 5.3.2 Performing Maintenance T asks 54 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 5.3.2.4 5 . 3 . 2 . 4 G r e a s in g t h e C O T I n s e r t Greasing t…
Major Maintenance
5.3.2 Performing Maintenance Tasks Maintenance Tasks for the Component Feed Device
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 53
5.3.2.3
5.3.2.3 Greasing the Cutting Blade
Greasing the Cutting Blade
Risk of injury when working near the tap e cutter
► Dismantle the waste slide. Read the service manual for your machine first.
► Install the waste slide. Also observe the following instructions:
Compone nt Supply - Manual Tables - Fitting Pr otections - SW Version
SXDX12V1V2 – Tape Cutter – Waste Tape Chute – Pay Attention to the Plastic Strips – SW Version
WARNING
Risk of injury when working near the cutter.
When working in the area of the tape cutter, move the component trolley out of the machine
and disconnect the machine from the mains supply and the compressed air supply.
► Wait until the operating pressure has dropped to 0 MPa.
► Always secure the machine against unauthorized reactivation.
► Do not reach into the tape cutter.
► Spray a bit of Interflon Fin grease [03020782-xx] into
a suitable container.
► Distribute the grease with a brush to the underside of
the fixed blade (1) as shown in the figure.
► Use a lint-free cloth to remove any excess grease
from the contact surfaces of the cutting blades (2)
and the grease nipple (3).
Manual tables only:
WARNING!
WARNING! There is a risk of injury on manual
tables without the two protections.
► Fit the two protections.
CAUTION!
Make sure that the plastic strips (1) (if present) are locat-
ed behind the plate (2) when you hook up the used tape
chute.
The black-yellow hatched label must be completely visi-
ble.
Major Maintenance
Maintenance Tasks for the Component Feed Device 5.3.2 Performing Maintenance Tasks
54 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
5.3.2.4
5.3.2.4 Greasing the COT Insert
Greasing the COT Insert
5.3.2.5
5.3.2.5 Greasing the Locator Bearing on the Component Trolley for X Feeders
Greasing the Locator Bearing on the Component Trolley for X Feeders
NOTICE
Grease the engaging pins
If the component trolley is frequently undocked, we recommend that you grease the engaging
pins.
► Grease the engaging pin (1) with a SIPLACE
cleaning tissue.
► Grease the hooks (2) on the left and right of the com-
ponent docking unit with a SIPLACE cleaning tissue.
► Repeat these tasks at all locations.
► Grease the rollers (1) (2 per side) on the changeover
table with a SIPLACE cleaning tissue.
► Repeat these tasks at all component trolleys.
Major Maintenance
5.3.2 Performing Maintenance Tasks Maintenance Tasks for the Component Feed Device
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 55
5.3.2.6
5.3.2.6 Greasing the Centering Strip on the Component Trolley/Feeder Table for X Feeders
Greasing the Centering Strip on the Component Trolley/Feeder Table for X Feeders
Centering guide rail at the component trolley (SX4 as ex
-
ample)
Centering guide rail at the manual table (DX4 as exam
-
ple)
► Apply "Surface Shield oil spray" [00328575-xx] to a
lint-free cloth and then thinly oil the centering strip (1).
Pay particular attention to the centering holes.
Alternatively you can also use a SIPLACE cleaning
tissue.
► Then wipe the centering strip with a lint-free cloth.
► Repeat these steps for all component trolleys and
manual tables.